Salta al contenuto principale
Aiuto

Dell Alienware 13 Display Assembly Replacement

Guida con Contributo Membro

Guida con Contributo Membro

Uno straordinario membro della nostra comunità ha realizzato questa guida. Non è gestita dallo staff iFixit.

Dell Alienware 13 Display Assembly Replacement

  • Autore: Terrence15
  • Stima il tempo: 20 - 45 minuti
  • Difficoltà: Moderato

In this guide, we will show you how to remove and replace the display assembly.

Passo 1 Open the Display  ¶ 

WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

Passo 1 Open the Display  ¶ 

Passo 2 Removing the Screws  ¶ 

Remove the screws that secure the hinge caps to the display hinges. Remove the screws that secure the hinge caps to the display hinges.

Passo 2 Removing the Screws  ¶ 

  • Remove the screws that secure the hinge caps to the display hinges.

Passo 3 Lift the Hinge Caps  ¶ 

Slide and lift the hinge caps off the display hinges.

Passo 3 Lift the Hinge Caps  ¶ 

  • Slide and lift the hinge caps off the display hinges.

Passo 4 Close the Display  ¶ 

Close the display and turn the computer over.

Passo 4 Close the Display  ¶ 

  • Close the display and turn the computer over.

Passo 5 Peeling the Adhesive Tape  ¶ 

Peel off the adhesive tape from the wireless card.

Passo 5 Peeling the Adhesive Tape  ¶ 

  • Peel off the adhesive tape from the wireless card.

Passo 6 Remove the Screw  ¶ 

Remove the screw that secures the wireless-card bracket to the wireless card.

Passo 6 Remove the Screw  ¶ 

  • Remove the screw that secures the wireless-card bracket to the wireless card.

Passo 7 Disconnecting the Antenna Cables  ¶ 

Disconnect the antenna cables from the wireless card.

Passo 7 Disconnecting the Antenna Cables  ¶ 

  • Disconnect the antenna cables from the wireless card.

Passo 8 Open the Display  ¶ 

Nessuna immagine

Passo 8 Open the Display  ¶ 

  • Turn the computer over and open the display.

Passo 9 Peeling the Adhesive Tapes  ¶ 

Peel off the adhesive tapes that secure the antenna cables to the system board.

Passo 9 Peeling the Adhesive Tapes  ¶ 

  • Peel off the adhesive tapes that secure the antenna cables to the system board.

  • Make note of the cable routing before removing any cable from its routing guide.

Passo 10 Removing the Antenna Cables  ¶ 

Remove the antenna cables from the routing guides on the display hinges.

Passo 10 Removing the Antenna Cables  ¶ 

  • Remove the antenna cables from the routing guides on the display hinges.

Passo 11 Disconnecting the Display Cable  ¶ 

Lift the connector latch and disconnect the display cable from the system board. Lift the connector latch and disconnect the display cable from the system board.

Passo 11 Disconnecting the Display Cable  ¶ 

  • Lift the connector latch and disconnect the display cable from the system board.

Passo 12 Removing the Display Cable  ¶ 

Remove the display cable from the routing guides on the display hinges.

Passo 12 Removing the Display Cable  ¶ 

  • Remove the display cable from the routing guides on the display hinges.

Passo 13 Disconnecting the Logo-Board Cable  ¶ 

Disconnect the logo-board cable from the system board and remove it from the routing guides on the display hinges.

Passo 13 Disconnecting the Logo-Board Cable  ¶ 

  • Disconnect the logo-board cable from the system board and remove it from the routing guides on the display hinges.

Passo 14 Removing the Screws  ¶ 

Remove the screws that secure the display assembly to the computer base.

Passo 14 Removing the Screws  ¶ 

  • Remove the screws that secure the display assembly to the computer base.

Passo 15 Lifting the Display Assembly  ¶ 

Lift the display assembly off the computer base.

Passo 15 Lifting the Display Assembly  ¶ 

  • Lift the display assembly off the computer base.

Passo 16 Align the Screw Holes  ¶ 

Nessuna immagine

Passo 16 Align the Screw Holes  ¶ 

  • Align the screw holes on the display hinges with the screw holes on the computer base.

Passo 17 Replacing the Screws  ¶ 

Replace the screws that secure the display hinges to the computer base.

Passo 17 Replacing the Screws  ¶ 

  • Replace the screws that secure the display hinges to the computer base.

Passo 18 Connecting the Logo-Board Cable  ¶ 

Route the logo-board cable through the routing guides on the display hinge and connect the logo-board cable to the system board.

Passo 18 Connecting the Logo-Board Cable  ¶ 

  • Route the logo-board cable through the routing guides on the display hinge and connect the logo-board cable to the system board.

Passo 19 Routing the Display Cable  ¶ 

Route the display cable through the routing guides on the display hinge.

Passo 19 Routing the Display Cable  ¶ 

  • Route the display cable through the routing guides on the display hinge.

Passo 20 Sliding the Display Cable  ¶ 

Slide the display cable into the connector on the system board and press down the latch to secure the cable.

Passo 20 Sliding the Display Cable  ¶ 

  • Slide the display cable into the connector on the system board and press down the latch to secure the cable.

Passo 21 Route the Antenna Cables  ¶ 

Route the antenna cables through the routing guides on the display hinges.

Passo 21 Route the Antenna Cables  ¶ 

  • Route the antenna cables through the routing guides on the display hinges.

Passo 22 Adhering the Tapes  ¶ 

Adhere the adhesive tapes that secure the antenna cables to the system board.

Passo 22 Adhering the Tapes  ¶ 

  • Adhere the adhesive tapes that secure the antenna cables to the system board.

Passo 23 Turn the Computer Over  ¶ 

Nessuna immagine

Passo 23 Turn the Computer Over  ¶ 

  • Close the display and turn the computer over.

Passo 24 Connecting the Antenna Cables  ¶ 

Connect the antenna cables to the wireless card.

Passo 24 Connecting the Antenna Cables  ¶ 

  • Connect the antenna cables to the wireless card.

Passo 25 Replace the Screw  ¶ 

Replace the screw that secures the wireless-card bracket to the wireless card. Replace the screw that secures the wireless-card bracket to the wireless card.

Passo 25 Replace the Screw  ¶ 

  • Replace the screw that secures the wireless-card bracket to the wireless card.

Passo 26 Adhering the Adhesive Tape  ¶ 

Adhere the adhesive tape to the wireless card.

Passo 26 Adhering the Adhesive Tape  ¶ 

  • Adhere the adhesive tape to the wireless card.

Passo 27 Open the Display  ¶ 

Nessuna immagine

Passo 27 Open the Display  ¶ 

  • Turn the computer over and open the display.

Passo 28 Align the Screw Holes  ¶ 

Align the screw holes on the hinge caps with the screw holes on the display hinges.

Passo 28 Align the Screw Holes  ¶ 

  • Align the screw holes on the hinge caps with the screw holes on the display hinges.

Passo 29 Replace the Screws  ¶ 

Nessuna immagine

Passo 29 Replace the Screws  ¶ 

  • Replace the screws that secure the hinge caps to the display hinges.