Salta al contenuto principale
Aiuto

Shark Rocket Powerhead AH401 Belt Replacement

This guide will help replace the belt of the Shark Rocket Powerhead AH401 Belt Replacement.

  • Autore: Shobhit Dabral
  • Stima il tempo: 20 - 30 minuti
  • Difficoltà: Moderato

Over time, the belt will wear off, which will cause the brushroll to stop rolling/spinning. This guide will demonstrate how to remove the belt properly. The belt is attached to the motor but the motor does not need to be removed. The screws holding the motor in place will have to be loosened in order for the belt to come off.

Sezioni
Strumenti

Passo 1 Belt  ¶ 

Remove the four screws by rotating counter-clockwise:

Passo 1 Belt  ¶ 

  • Remove the four screws by rotating counter-clockwise:

  • One 12 mm screw with a T10 Torx screwdriver

  • Three 14 mm screw with a T15 Torx screwdriver

Passo 2  ¶ 

Remove the grey filter plate by simply lifting upward. Remove the 14mm screw by rotating counter clockwise with a T10 Torx screwdriver. Remove the 14mm screw by rotating counter clockwise with a T10 Torx screwdriver.

Passo 2  ¶ 

  • Remove the grey filter plate by simply lifting upward.

  • Remove the 14mm screw by rotating counter clockwise with a T10 Torx screwdriver.

Passo 3  ¶ 

Remove three 10mm screws by rotating counter-clockwise with a T15 Torx screwdriver.

Passo 3  ¶ 

  • Remove three 10mm screws by rotating counter-clockwise with a T15 Torx screwdriver.

Passo 4  ¶ 

Remove the airpath grille from the side of the motor compartment by pulling out and away from the attached area. Remove the airpath grille from the side of the motor compartment by pulling out and away from the attached area.

Passo 4  ¶ 

  • Remove the airpath grille from the side of the motor compartment by pulling out and away from the attached area.

Passo 5  ¶ 

Remove the motor compartment panel by lifting up and away from the device. Remove the motor compartment panel by lifting up and away from the device.

Passo 5  ¶ 

  • Remove the motor compartment panel by lifting up and away from the device.

Passo 6  ¶ 

Remove one 14mm screw by rotating counter-clockwise with a T15 Torx screwdriver. Remove one 14mm screw by rotating counter-clockwise with a T15 Torx screwdriver.

Passo 6  ¶ 

  • Remove one 14mm screw by rotating counter-clockwise with a T15 Torx screwdriver.

Passo 7  ¶ 

Disconnect  the motor side panel by lifting the motor and panel up and out. This step may require some wiggling to loosen the panel before it becomes free.

Passo 7  ¶ 

  • Disconnect the motor side panel by lifting the motor and panel up and out.

  • This step may require some wiggling to loosen the panel before it becomes free.

Passo 8  ¶ 

Remove one 9mm screw by rotating counter-clockwise with a Phillips #2 screwdriver.

Passo 8  ¶ 

  • Remove one 9mm screw by rotating counter-clockwise with a Phillips #2 screwdriver.

  • This screw allows the side panel to be removed.

Passo 9  ¶ 

Remove the side panel by pulling the panel out and away from the motor. The side panel is connected with clips which connect near the brushroll axle.

Passo 9  ¶ 

  • Remove the side panel by pulling the panel out and away from the motor.

  • The side panel is connected with clips which connect near the brushroll axle.

Passo 10  ¶ 

Loosen the two screws by rotating counter clockwise with a T15 Torx screwdriver. The screws only need to be loosened in order to free the belt.

Passo 10  ¶ 

  • Loosen the two screws by rotating counter clockwise with a T15 Torx screwdriver.

  • The screws only need to be loosened in order to free the belt.

Passo 11  ¶ 

Remove the belt by pulling the belt away from the axle. Remove the belt by pulling the belt away from the axle.

Passo 11  ¶ 

  • Remove the belt by pulling the belt away from the axle.