Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement

Cosa ti serve

  1. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement, Heater: passo 1, immagine 1 di 2 Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement, Heater: passo 1, immagine 2 di 2
    • Disconnect the power plug located on the back of the massage pillow.

    • Please do this step carefully in order to avoid electric shock.

  2. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 2, immagine 1 di 2 Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 2, immagine 2 di 2
    • Unzip the cover. You can locate the zipper at the back of the massage pillow.

    • Take out the pillow so that you can manage the heater completely.

  3. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 3, immagine 1 di 1
    • Use a Phillips JIS #1 screwdriver to remove the screw at the center of the heater.

    • The screw is 8.0mm.

  4. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 4, immagine 1 di 2 Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 4, immagine 2 di 2
    • Remove the entire heater from the pillow.

    • You can see a green circuit board after removing the heater.

  5. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 5, immagine 1 di 1
    • Using the Phillips JIS #1 screwdriver, remove the three screws circled in the picture.

    • All three screws are 8.0mm, which are the same size as the previous one. They are interchangeable.

  6. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 6, immagine 1 di 1
    • Now you can take out the circuit board. There will be two wires attached to the circuit board.

    • If you prefer, you can clean the circuit board gently with dry tissues to remove the sticky lubricant.

  7. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 7, immagine 1 di 1
    • Use the pry bar to separate the wire from the white main board.

    • Before prying, check if you removed the power plug from the outlet and the massage pillow.

  8. Zyllion ZMA-13-BK Shiatsu Massage Pillow Heater Replacement: passo 8, immagine 1 di 1
    • Using your soldering station, remove the wires from the circuit board.

    • If you don't know how to solder, you can check out this guide: How To Solder and Desolder Connections

    • Soldering can be dangerous. Be cautious of high heat soldering tools.

    • Now, you can separate the circuit board completely to replace with a new heater.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Yuchen Li

Membro da: 09/28/15

125 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 14-2, Green Fall 2015 Membro di Cal Poly, Team 14-2, Green Fall 2015

CPSU-GREEN-F15S14G2

4 Membri

8 Guide realizzate

2 Commenti

Hi YuChen, nice work! Do you know from where I can find the switch for this heater? If you can tell me the part number, I can try looking it up on eBay. Thanks!

Abhishek Srivastava - Replica

YuChen, by any chance do you know where I can get the whole covering of this Shiatsu Massage Pillow. The fabric of mine has deteriorated and torn off. I have been trying to find one using Google search but was unable to find. Can you help, Thank you

gamesake2 - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 39

Tutti i Tempi: 5,929