Salta al contenuto principale

Zoom Q3HD Handy Video Recorder Lens Cleaning

Cosa ti serve

  1. Zoom Q3HD Handy Video Recorder Lens Cleaning, Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 1, immagine 1 di 1
    • Remove the two screws from the bottom of the device.

    • Make sure to put your screws in a safe place.

  2. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 2, immagine 1 di 1
    • Flip the device over and remove the four screws bordering the grate of the device.

  3. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 3, immagine 1 di 1
    • On the front of the device, slide the battery compartment cover off by pushing inward and sliding downward.

  4. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 4, immagine 1 di 1
    • Remove the two screws from the lip of the battery compartment.

  5. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 5, immagine 1 di 1
    • Remove the final screw from the bed of the battery compartment.

  6. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 6, immagine 1 di 1
    • WARNING: Pieces may become loose when you separate the device in half!

    • Run the pry tool along the edges of the device to begin separating the device in two halves.

  7. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 7, immagine 1 di 2 Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 7, immagine 2 di 2
    • REMINDER: Pieces may become loose when you separate the device in half!

    • Apply upward pressure to fully separate the device into two halves.

  8. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 8, immagine 1 di 1
    • WARNING: If you’re not careful with keeping the screen close to the board, you will rip off the ribbon attaching the screen to the circuit board.

    • Lift display screen keeping the top half close to the board.

  9. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 9, immagine 1 di 1
    • Gently flip the black clip up attaching the ribbon of the screen to the circuit board.

  10. Zoom Q3HD Handy Video Recorder Lens Cleaning: passo 10, immagine 1 di 1
    • Gently slide the ribbon from the circuit board, removing the screen.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Team

Ohio State, Team 1-1, Mccook Fall 2014 Membro di Ohio State, Team 1-1, Mccook Fall 2014

OSU-MCCOOK-F14S1G1

4 Membri

1 Guida realizzata

3 Commenti

My zoom q3HD only have the red light turned on when powering up. No display at all. What is happening? How can I claim warranty? I didn't use the device more than a year. Help me

stancalvin - Replica

This is not comlete, leaves you half way through, would be great if you could finish this, thank you.

smoldas.l - Replica

Yes it would be good to see it finished. I am half way through taking mine apart to clean the lens amd i don't know if i should proceed or not. Its the 2nd time the lens has fogged up. My 2nd q3hd.

steven kemsley - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 10

Tutti i Tempi: 1,934