Introduzione

The only requirements for this replacement guide are the right tools, new battery terminals, and device ready before starting the guide. Terminals should be replaced when the device stops powering on despite the replacement of new batteries or due to the corrosion of terminals.

  1. Place device on table facing down.
    • Place device on table facing down.

    • Remove the battery cover, with index finger press protruding tab towards "OPEN".

    Aggiungi Commento

  2. If batteries are present, remove them in order to reveal the terminals at the bottom of the device.
    • If batteries are present, remove them in order to reveal the terminals at the bottom of the device.

    Aggiungi Commento

    • With the flat end of the black plastic spudger, pry the terminal away from the case.

    • Use the small blue plastic opening tool to lift the terminal out of the device. Repeat for the adjacent terminal.

    • When lifting the terminal out, the metal wire of the terminal must move past the plastic protrusion that keeps the battery terminal in place.

    Aggiungi Commento

    • Remove four rubber feet using fingernails to access the four screws underneath.

    Aggiungi Commento

    • For the terminals directly connected to the motherboard, unscrew eight (PH #1), 9 mm screws (two located on the top back side, two in the center of back side of device right above the battery cover, and four under the rubber feet).

    • An electronics screwdriver narrow enough to fit in hole (3.5mm diameter), but long enough to reach the screws (at least 2cm) will be required to unscrew the two screws in the center of back side of the device.

    Aggiungi Commento

    • Place device face up and remove the four knobs using the flat end of the plastic opening tool.

    Aggiungi Commento

    • Carefully lift up the top of the device and gently set aside.

    Aggiungi Commento

    • Unscrew three (PH #1), 7mm screws from the button board near the display and gently flip over.

    Aggiungi Commento

    • Using a plastic opening tool, unlatch the clip and carefully unplug the ribbon connector from the device.

    • Set the button board aside.

    Aggiungi Commento

    • Unscrew four (PH #1), 8mm screws from the motherboard.

    Aggiungi Commento

    • Disconnect wire from motherboard using tweezers.

    • Do not touch the motherboard with metal tweezers. Only touch the plastic part of the plugged-in wire.

    Aggiungi Commento

    • Turn device 180 degrees to unscrew two (PH #1), 8mm screws from the mic connector.

    Aggiungi Commento

    • Gently remove three ribbon connectors from the base of the device. One is connected to the mic connector, the other two are on the top of the device next to the "LINE OUT" plug-in (directly behind the device display screen).

    • Use tweezers to remove the two ribbon connectors behind the display screen because it is difficult to remove them only using hands.

    • Avoid touching anything but the ribbon connectors with the metal tweezers.

    Aggiungi Commento

    • Gently lift off motherboard from the base of the device.

    Aggiungi Commento

    • Taking care not to damage other components on the motherboard, use a soldering iron to undo the soldering that holds the terminals to the motherboard.

    Aggiungi Commento

    • Flip motherboard over and remove the black tape covering the battery terminal.

    • Replace with new terminal.

    • Resolder the terminals to the motherboard.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Rachel Calder

Membro da: 14/02/2018

666 Reputazione

5 Guide realizzate

Team

USF Tampa, Team S5-G2, Eyestone Spring 2018 Membro di USF Tampa, Team S5-G2, Eyestone Spring 2018

USFT-EYESTONE-S18S5G2

4 Membri

8 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 43

Tutti i Tempi: 296