Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Zeki TBQG884B Digitizer Touch Screen

Introduzione

This guide requires three prerequisite guides for the proper replacement of the digitizer screen on the front of the Zeki tablet. Please, take a moment to familiarize yourself with those guides. They can be found in the details section of this guide.

Cosa ti serve

  1. Zeki TBQG884B Digitizer Touch Screen, Rear Case: passo 1, immagine 1 di 2 Zeki TBQG884B Digitizer Touch Screen, Rear Case: passo 1, immagine 2 di 2

    • Remove the two screws from the end of the device where the ports are located using a Phillips #1 screwdriver.

    Traduci

  2. Zeki TBQG884B Digitizer Touch Screen: passo 2, immagine 1 di 1

    • Place the tablet down so that the screen is facing away from you.

    • Insert the tip of your opening tool into the small gap between the gray and white plastic covering. Pry it open and you should hear the clips opening up.

    • Gently work your way around the perimeter of the tablet's edge.

    Traduci

  3. Zeki TBQG884B Digitizer Touch Screen: passo 3, immagine 1 di 2 Zeki TBQG884B Digitizer Touch Screen: passo 3, immagine 2 di 2

    • Remove the back cover

    • Remove any tape on the speaker and detach the speaker from the back plate.

    • The speaker is connected to the motherboard by two soldered wires. Don't break them when you remove the speaker.

    Traduci

  4. Zeki TBQG884B Digitizer Touch Screen, Motherboard: passo 4, immagine 1 di 1

    • Disconnect the Wi-Fi antenna cable from the motherboard.

    Traduci

  6. Zeki TBQG884B Digitizer Touch Screen: passo 5, immagine 1 di 1

    • Using the Phillips #1 screwdriver, remove the three screws from the motherboard..

    Traduci

  7. Zeki TBQG884B Digitizer Touch Screen: passo 6, immagine 1 di 1

    • Open the ZIF connector. Then, remove the ribbon that connects the motherboard and the screen.

    Traduci

  8. Zeki TBQG884B Digitizer Touch Screen: passo 7, immagine 1 di 1

    • Disconnect the other ZIF connector on the opposite side of the motherboard.

    Traduci

  9. Zeki TBQG884B Digitizer Touch Screen: passo 8, immagine 1 di 1

    • Remove the motherboard and now reinsert all connectors into a new motherboard.

    • In order to disconnect the battery and speaker wires from the motherboard, soldering is required. Be cautious as the soldering iron is hot.

    Traduci

  10. Zeki TBQG884B Digitizer Touch Screen, LCD Screen: passo 9, immagine 1 di 1

    • Use an opening tool to detach the clip between the front frame, and the metal loader.

    • There are several clips on each side of the frame. Detach ALL of them before you open the loader.

    Traduci

  11. Zeki TBQG884B Digitizer Touch Screen: passo 10, immagine 1 di 1

    • Lift the metal loader up and separate it from the LCD screen.

    • Detach each piece slowly to avoid damaging or dropping any fragile parts.

    Traduci

  12. Zeki TBQG884B Digitizer Touch Screen, Digitizer Touch Screen: passo 11, immagine 1 di 1

    • The display is now separated from the digitizer.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 9 altri collaboratori

David Wyman

Membro da: 09/16/15

343 Reputazione

3 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

IUPUI, Team 1-3, Harley Fall 2015 Membro di IUPUI, Team 1-3, Harley Fall 2015

IUPUI-HARLEY-F15S1G3

5 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 800