Menü

Le tue impostazioni

Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi
Il Mio Carrello

Sembra che il tuo carrello sia vuoto

Sfoglia il Nostro Negozio

Yamaha YPG-225 Display Replacement

In evidenza

Scritto Da: Lonnie Bissmeyer (e 3 altri collaboratori)
  • Commenti: 1
  • Preferiti: 2
  • Completamenti: 1

Guida In Evidenza

Difficoltà

Moderato

Passi

14

Tempo Necessario

20 minuti

Sezioni

4

Contrassegni

4

Grammar Police

Vigilanza sulla Grammatica

Adotta il tuo insegnante di inglese interno e contribuisci a migliorare la grammatica di questa guida!

Needs Better Images

Necessarie Immagini Migliori

Delle foto più belle renderanno migliore questa guida. Contribuisci scattando, modificando o caricando immagini nuove!

Featured Guide

Guida In Evidenza

Questa guida è stata giudicata eccezionalmente ben fatta dallo staff iFixit.

Student In Progress

Studente In Lavorazione

Questa guida è in lavorazione da parte di studenti laboriosi.

Introduzione

Use this guide to install a replacement keyboard display.

Strumenti

Acquista questi strumenti

Parti

Nessuna parte specificata.

  1. Turn the keyboard over so that the keys are facing the ground.

    • Turn the keyboard over so that the keys are facing the ground.

    Traduci

  2. Pop the tabs on the battery casing and remove it from the back plate.

    • Pop the tabs on the battery casing and remove it from the back plate.

    Traduci

  3. Locate the six batteries and remove them from the battery cavity.

    • Locate the six batteries and remove them from the battery cavity.

    Traduci

  4. Remove the six 10mm screws at the top of the backplate.

    • Remove the six 10mm screws at the top of the backplate.

    Traduci

  5. Remove the seven 12mm screws in the middle of the back plate.

    • Remove the seven 12mm screws in the middle of the back plate.

    Traduci

  6. Kit di riparazione batterie iPhone

    Solo $29.99

    Buy Now

    Kit di riparazione batterie iPhone

    Solo $29.99

    Buy Now

  7. Remove the eight 10mm screws from the side and the bottom of the back plate.

    • Remove the eight 10mm screws from the side and the bottom of the back plate.

    Traduci

  8. As the face plate is no longer connected to the body of the keyboard, be careful to not drop the body when performing this step.

    • As the face plate is no longer connected to the body of the keyboard, be careful to not drop the body when performing this step.

    • Flip over the keyboard

    Traduci

  9. Lifting from the front and the back of the face plate equally, pull the face plate up and then back, away from the keyboard. Be careful when removing the face plate. There are wires attached.

    • Lifting from the front and the back of the face plate equally, pull the face plate up and then back, away from the keyboard.

    • Be careful when removing the face plate. There are wires attached.

    Traduci

  10. Locate the main circuit board - it should be toward the middle of the detached face plate.

    • Locate the main circuit board - it should be toward the middle of the detached face plate.

    Traduci

  11. Use a plastic opening tool or spudger to carefully pry up the beige ribbon connectors and remove the wires from them. Be sure to use a tool that is ESD safe!

    • Use a plastic opening tool or spudger to carefully pry up the beige ribbon connectors and remove the wires from them.

    • Be sure to use a tool that is ESD safe!

    • Use a slightly upward force as parallel to the ground as possible.

    • Be sure to make a mental note or jot down the locations of the specific ribbon cables. Some are in close proximity to each other and it can be easy to forget which ribbon goes where.

    • Be sure to unplug the smaller ribbon that connects to a different circuit board.

    • Take care not to use too much force. The connectors are fragile, the ribbon wires are easily bent, and too much force may damage the circuit board if you happen to miss.

    Traduci

  12. Move the ribbons out of the way and remove the eight 10mms crews in the middle that hold the circuit board down.

    • Move the ribbons out of the way and remove the eight 10mms crews in the middle that hold the circuit board down.

    • Remove the two 12mm screws in the corner of the circuit board.

    Traduci

  13. Remove this wire carefully by hand.

    • Remove this wire carefully by hand.

    Traduci

  14. Completely remove the circuit board from the face plate.

    • Completely remove the circuit board from the face plate.

    Traduci

  15. Slide out the screen from its case on the circuit board.

    • Slide out the screen from its case on the circuit board.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 3 altri collaboratori

Lonnie Bissmeyer

Membro da: 16/09/2012

336 Reputazione

4 Guide realizzate

Distintivi: 11

+8 altri distintivi

Team

Cal Poly, Team 2-62, Propen Fall 2012 Membro di Cal Poly, Team 2-62, Propen Fall 2012

CPSU-PROPEN-F12S2G62

2 Membri

6 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 30

Tutti i Tempi: 2,951