Questa traduzione potrebbe non riflettere gli aggiornamenti più recenti dalla guida originale. Aiuta ad aggiornare la traduzione o visualizza la guida d'origine.
Introduzione
Il jack audio sul tuo controller Xbox potrebbe avere problemi di connessione con dispositivi audio oppure non inviare nessun segnale audio. Se questo è il tuo problema potrebbe essere necessaria la sostituzione del jack da 3.5mm. Questa guida ti insegnerà come arrivare al jack audio 3.5mm e rimuoverlo sul tuo controller wireless Xbox One Modello 1708.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the battery cover toward the top of the controller to remove it.
-
Lift up the batteries or the battery pack from the battery compartment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a plastic opening tool into the top seam, and gently work the opening tool to the bottom of the controller.
-
Continue using the opening tool to gently pry the side plate off of the controller.
-
Repeat this process for the second side plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently peel the battery label or punch a hole in the center of the sticker in the battery compartment to reveal the hidden screw.
-
Remove the five 9mm torx-9 security screws from the back of the controller.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Tape the Rumbler/shock motors in place.
-
This will prevent the motors from falling out.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the controller so the front plate is facing up.
-
Lift the front cover off of the controller.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the controller face down and gently lift the rear plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the device over and remove the directional pad by gently pulling it away from the controller.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the device over and remove the two 7mm torx-6 screws in the bottom left and right corners.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Firmly grasp the top and bottom motherboards in opposite hands, then gently pull them apart.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the audio port from the bottom mother board.
-
Per riassemblare il tuo dispositivo, segui queste istruzioni al contrario.
Per riassemblare il tuo dispositivo, segui queste istruzioni al contrario.
Annulla: non ho completato questa guida.
Altre 24 persone hanno completato questa guida.
Un ringraziamento speciale a questi traduttori:
80%
Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›
6 Commenti
Where do I get a replacement audio port?
Hey Cory,
Sorry, didn’t realize that the part wouldn’t get listed for the guide. I looked around a bit and I would say that it seems the best place to pick these up is ebay.
I found one on there from a reputable seller for $3:
https://www.ebay.com/itm/Repair-Part-3-5...
The seller seems to sell a good amount of these.
Hope that helps!
I removed the 3.5mm jack, cleaned the contacts with a fibre glass contact cleaning brush, and then cleaned both the audio connector and the gold plated PCB pads with IPA, reassembled, and everything worked perfectly. Thanks for the guide, it’s boarder line perfect ;-)