Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Xbox One S Hard Drive Assembly

Scritto Da: Victoria Law (e 3 altri collaboratori)
  • Commenti: 8
  • Preferiti: 1
  • Completamenti: 4

Difficoltà

Moderato

Passi

10

Tempo Necessario

10 minuti

Sezioni

3

Contrassegni

0

Introduzione

If you want to replace the hard drive with one that has a larger capacity, this guide will teach you how to replace the hard drive.

Strumenti

Acquista questi strumenti

Parti

Nessuna parte specificata.

  1. Flip the Xbox One S so that the bottom of the case is facing upward.

    • Flip the Xbox One S so that the bottom of the case is facing upward.

    Modifica

  2. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.

    • Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.

    • Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • You will hear clicking sounds when you are prying the case open. It may be fairly difficult to remove the bottom.

    • It's possible that the clips may break when you remove the bottom from the case.

    • We recommend starting at one corner and sliding the prying tool along the edges of the Xbox One S. Once the first few clips are opened you can lift the cover up to find the remaining clips.

    Modifica

  3. Once all of the clips are opened, remove the bottom part of the case.

    • Once all of the clips are opened, remove the bottom part of the case.

    Modifica

  4. Find all of the green screws on the metal case labeled F1 through F6. Take the T10 Torx screwdriver and remove the six 50 mm long screws.

    • Find all of the green screws on the metal case labeled F1 through F6.

    • Take the T10 Torx screwdriver and remove the six 50 mm long screws.

    Modifica

  5. Essential Electronics Toolkit

    Small Toolkit. Big Possibilities.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits

  6. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal. The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal.

    • The port cover is held in place with rivets. Insert a pry tool gently between the top cover and metal casing on both sides to prepare the cover for removal.

    Modifica

  7. Gently separate the interior case from the white exterior case using the appropriate method. Gently separate the interior case from the white exterior case using the appropriate method.

    • Gently separate the interior case from the white exterior case using the appropriate method.

    Modifica

  8. Flip the interior case so it is fan side upward.

    • Flip the interior case so it is fan side upward.

    Modifica

  9. Gently pop and lift the metal panel on top of the interior case to access the hardware. It should come right off.

    • Gently pop and lift the metal panel on top of the interior case to access the hardware. It should come right off.

    Modifica

  10. To replace the hard drive, remove the two 10 mm T-10 Torx screws, C3 and C4, from the backside of the Xbox One S. To replace the hard drive, remove the two 10 mm T-10 Torx screws, C3 and C4, from the backside of the Xbox One S.

    • To replace the hard drive, remove the two 10 mm T-10 Torx screws, C3 and C4, from the backside of the Xbox One S.

    Modifica

  11. Gently disconnect the hard drive from the motherboard (at the two plastic connector bodies). Gently disconnect the hard drive from the motherboard (at the two plastic connector bodies). Gently disconnect the hard drive from the motherboard (at the two plastic connector bodies).

    • Gently disconnect the hard drive from the motherboard (at the two plastic connector bodies).

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Autore

con 3 altri collaboratori

Victoria Law

Membro da: 26/04/2017

667 Reputazione

3 Guide realizzate

Distintivi: 13

+10 altri distintivi

Team

Cal Poly, Team S22-G3, Livingston Spring 2017 Membro di Cal Poly, Team S22-G3, Livingston Spring 2017

CPSU-LIVINGSTON-S17S22G3

4 Membri

33 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 17

Ultimi 30 Giorni: 108

Tutti i Tempi: 2,350