Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Nei seguenti passaggi, rimuoverai la grata superiore, assicurata al pannello dai tredici fermi di plastica mostrati nella foto.
-
-
-
Orienta la console in modo che le parole "XBOX 360" sui lati siano rivolte verso l'alto e il frontalino sia rivolto verso sinistra.
-
Inserire lo spudger di metallo tra lo sfiato superiore e la mascherina superiore vicino al retro della Xbox.
-
Ruota lo spudger verso l´esterno dalla console, facendo leva sul bordo dello sfiato della ventola fino a liberare i due fermagli di plastica.
-
-
-
Inserisci lo spudger tra la grata di sfogo e la cornice superiore, lungo il lato sinistro della console.
-
Nello stesso modo descritto sopra, inizia a far leva sul lato sinistro dello sfiato superiore per staccarlo dalla cornice.
-
Continua a fare leva lungo tutto il lato sinistro per sganciare tutte le clip su questo lato.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the fan vent up from the freed left side to disengage the clips along the right side.
-
Remove the entire fan vent.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
In the following steps, you will be releasing the six clips highlighted in red.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a metal spudger through the front-most slit on the left edge of the top bezel and between the bottom edge of the clip and the left case, as described above.
-
Simultaneously rotate the spudger away from the console and pull up on the top bezel to free the clip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the same method described above, free the two remaining clips along the left edge of the top bezel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the entire top panel with your hands, lift up the entire left edge high enough to rest the separated clips on top of the left case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the console so that the rear of the Xbox 360 S is facing to the right, and the right case is facing you.
-
Insert a metal spudger through the rear-most slit on the right edge of the top bezel and between the bottom edge of the clip and the right case.
-
While lifting up on the top bezel with your fingers, rotate the spudger away from the console to free the clip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
In the same manner as described in the previous steps, release the middle and front clips along the right edge of the top panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single T10 Torx screw holding in the wireless card.
-
Pull the Wi-Fi board out of the console.
-
Annulla: non ho completato questa guida.
Altre 37 persone hanno completato questa guida.
4 Commenti
My Slim came without the wifi board, and subsequently without the holding screw.
Anyone know the thread, size, or depth of a replacement screw I could use to hold the replacement in? It seems like it won't go anywhere with the pseudo-USB connector in place, but I'd like to be positive.
Any help would be appreciated!
Tuve ese mismo problema. Fui a una tienda y el técnico tuvo que quitarle la tarjeta de WiFi a otro xbox porque no hay repuesto
Worth noting.. Before you purchase a new wifi card, try taking it out and reseating it. Just had to do that with mine when the wifi suddenly stopped working. Once I pulled the card and put it back in, it worked beautifully.
Also, for clarification, you are opening the side OPPOSITE the side with the hard drive.
Is it possible to replace it a newer, updated, improved WiFi card that is faster?