Introduzione

If your power cord is broken and your blender will not turn on, follow these steps to replace it.

  1. With the bottom of the blender facing up, use a Phillips #2 screwdriver to remove the 4, 1/2 inch long screws in the corners of the device. Ensure the blender is off and unplugged before starting.
    • With the bottom of the blender facing up, use a Phillips #2 screwdriver to remove the 4, 1/2 inch long screws in the corners of the device.

    • Ensure the blender is off and unplugged before starting.

  2. Using a metal spudger, pry up one side of each of the rubber feet. Note that one side of each foot is glued down; pry up the non-glued side.
    • Using a metal spudger, pry up one side of each of the rubber feet.

    • Note that one side of each foot is glued down; pry up the non-glued side.

  3. Using the same Phillips #2 screwdriver, unscrew the 1/2 inch long screw under each of the feet.
    • Using the same Phillips #2 screwdriver, unscrew the 1/2 inch long screw under each of the feet.

  4. Pull off the base and remove the plastic housing underneath. Pull off the base and remove the plastic housing underneath.
    • Pull off the base and remove the plastic housing underneath.

  5. Spedizione gratuita per tutti gli ordini superiori a 100 US$ o contenenti un Kit Attrezzi Pro Tech!

    Sfoglia il Nostro Negozio
  6. On the underside of the base, unscrew the three 3/8" long screws on the plastic piece holding the power cord in place using a Phillips #1 screwdriver. Pull the plastic cover off.
    • On the underside of the base, unscrew the three 3/8" long screws on the plastic piece holding the power cord in place using a Phillips #1 screwdriver.

    • Pull the plastic cover off.

  7. Using a wire cutter, cut the three wires of the power cord.
    • Using a wire cutter, cut the three wires of the power cord.

  8. Pull the cut power cord through the base. Then thread the replacement cord back through and re-attach the plastic cover.
    • Pull the cut power cord through the base.

    • Then thread the replacement cord back through and re-attach the plastic cover.

  9. Strip about  an inch of insulation off of the snipped power cord and your replacement cord. Twist each strand of wires together to keep them neat. Twist each strand of wires together to keep them neat.
    • Strip about an inch of insulation off of the snipped power cord and your replacement cord.

    • Twist each strand of wires together to keep them neat.

  10. Twist together the wires from the replacement cord to the wires still attached to the  blender. Solder the connection if possible.
    • Twist together the wires from the replacement cord to the wires still attached to the blender.

    • Solder the connection if possible.

  11. Wrap all the connections in electrical tape or heat shrink tubing. Wrap all the connections in electrical tape or heat shrink tubing.
    • Wrap all the connections in electrical tape or heat shrink tubing.

Conclusione

To reassemble your device, follow steps 1-5 in reverse order.

Un'altra persona ha completato questa guida.

Cole Gillespie

Membro da: 19/04/2018

464 Reputazione

2 Guide realizzate

Team

Cal Poly, Team S25-G16, Maness Spring 2018 Membro di Cal Poly, Team S25-G16, Maness Spring 2018

CPSU-MANESS-S18S25G16

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 34