Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place your thumb and forefinger on the blood pressure (NIBP) hose connector. Squeeze the side tabs until the connector releases.
-
Pull the connector away from the connector port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place your thumb and forefinger on the Pulse oximetry (SpO2 or combined SpO2/SpHb) cable connector. Squeeze the side tabs until the connector releases.
-
Pull the connector away from the connector port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the temperature probe and pull it up to remove it from the monitor.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the cover of the temperature module by pressing the tab and sliding the cover to the right.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Depress the spring tab on the temperature probe cable connector and withdraw it from the probe port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the flathead screw on the USB networking door.
-
Loosen the captive Phillips #2 screw securing the monitor to the stand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Holding the monitor securely, open the USB networking door.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Detach any accessory USB cables from USB ports on the monitor.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a coin into the slot and push to open.
-
Remove the battery cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the plastic label to remove the battery from its recess.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four Phillips #2 screws (labeled 14 in the service manual) from the rear housing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With the handle/alert bar facing you, begin to lift the rear housing from the left side, holding the right side securely.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the fan cable (labeled connector A in the service manual) from its socket in the power supply.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unplug the small USB connector from its socket (labeled J4 in the service manual).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the communications power cable from its socket (labeled J50 in the service manual).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unplug the large USB connector from its socket (labeled J8 in the service manual).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Press the tab on the ethernet cable and unplug it from its socket (labeled J9 in the service manual).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The power supply cable is secured by an interlocking connector that must be held open to unplug the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the power supply cable firmly and lift both it and the spudger from the channel in the power supply housing to unplug the connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the four T10 Torx screws from the power supply cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unplug the AC power harness connectors from the IEC connector with a pair of pliers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the ground connector from the ground plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat end of a spudger to lift the power supply up off the posts in the rear housing.
-
Lift and remove the power supply from the rear housing.
-
Annulla: non ho completato questa guida.
Un'altra persona ha completato questa guida.