Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unplug any cables from the USB, power, display or DVI-D ports by gripping the cord by the connector and pulling straight out of the port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the device screen down on a flat surface.
-
Remove eight 10mm Phillips #2 screws (four on each leg of the stand) by turning the screwdriver counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the stand up and away from the rest of the device so the legs separate from the mounting plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove eighteen 10.2mm Phillips #1 screws from the perimeter of the back panel by turning the screwdriver counterclockwise.
-
Remove one 11.9mm Phillips #1 screw from the center of the back panel.
-
Remove two 10.2mm Phillips #1 screws from underneath hinged panels in the bottom right and left corners.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the back panel up by a corner and insert a plastic opening tool in the gap.
-
Slide the tool along the gap around the perimeter of the device while lifting to unlatch the back panel.
-
Remove the panel by lifting it up and off of the device.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Detach the small black wire connecting the back metal plate to the USB video port by removing the one 8 mm Phillips #2 screw from the back metal plate and turning the screwdriver counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 8 mm Phillips #2 screws from the metal button plate by rotating the screwdriver counterclockwise.
-
Remove the metal button plate from the back metal plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the button wires from the support clip by pushing down on the clip.
-
Detach the button wires from the button board by pulling the button wires away from the board.
-
Place the button board back in to the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the eight (four on each plate) 10.2mm Phillips #2 screws with locking washers from the metal mounting plates by rotating the screwdriver counterclockwise.
-
Remove the two metal mounting plates.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the sixteen 8 mm Phillips #2 screws with flanges from the horizontal side of the plate by turning the screwdriver counterclockwise.
-
Remove the ten 8 mm Phillips #2 screws with flanges from the vertical sides of the plate by turning the screwdriver counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the back metal plate by lifting up along one edge , then lifting the plate off and away from the device.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 7.8mm Phillips #2 screws from the right back panel connected to the power port by turning the screwdriver counterclockwise.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the power port and attached daughterboard out of the device.
-
Remove the wires from the daughterboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 8 mm Phillips #2 screws from the daughterboard by turning the screwdriver counterclockwise.
-
Detach the metal cover from the power port.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Desolder the connections the power port connections using a soldering iron.
-
Remove the power port from the daughterboard by lifting it off.
-
Annulla: non ho completato questa guida.
Altre 3 persone hanno completato questa guida.
7 Commenti
My 24 HD blue power light comes on and off about once a second, you can hear the fan start and stop. Is a faulty power board the reason or is it the ps block ?
Is there any where I can get this part the circuit board is damaged
any information regarding where to buy this component