Introduzione

This guide is meant to teach the reader to install a new viewfinder mirror and lens. If the lens or mirror are no longer working or broken, this guide will help the reader replace them with new ones.

Parti

Nessuna parte richiesta.

  1. Flip the camera over so the bottom is facing you.
    • Flip the camera over so the bottom is facing you.

    Aggiungi Commento

  2. Open the cover on the bottom by sliding it in the direction of the arrow.
    • Open the cover on the bottom by sliding it in the direction of the arrow.

    Aggiungi Commento

    • Remove the batteries by pulling up on the top with your fingers.

    Aggiungi Commento

    • Unless otherwise stated, use a phillips #00 screwdriver to remove screws.

    • Remove the two 4.70mm screws in the bottom of the plastic casing.

    Aggiungi Commento

    • Remove the four 4.70mm screws in the left side of the camera.

    Aggiungi Commento

    • Now on the side with the strap, remove the other four 4.70mm screws.

    Aggiungi Commento

    • Use your thumbs to pry the case apart.

    • It is easiest to pry to case apart if your start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a tool such as a Spudger or Plastic Opening tool.

    Aggiungi Commento

    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of case about half an inch. This may be difficult and force is necessary.

    Aggiungi Commento

    • While pulling the camera out of the case, note the small soft plastic cover on the side of the camera. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out about an inch and a half, pull the device out completely.

    • When completely removing the device from the case, use a firm grasp with your hands for stability and control.

    Aggiungi Commento

    • Turn the camera so that the LCD screen is facing you.

    • If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.

    • You will not be able to complete this guide without removing the casing completely.

    Aggiungi Commento

    • Remove the four 4.40mm screws that hold the LCD screen in place to the frame.

    Aggiungi Commento

    • Allow the LCD screen to flip down. This will expose the electric strip connecting the screen to the camera.

    Aggiungi Commento

    • Look for where the yellow electric strip is attached to the camera. There is a plastic grey bar and a white base holding this strip in place.

    • Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.

    Aggiungi Commento

    • Unplug the connected red and white wires. They will come out with the small white casing.

    Aggiungi Commento

    • Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

    Aggiungi Commento

    • Remove bottom left LCD mounting frame screw.

    • Remove LCD screen from camera. Screen should come loose after screw is removed. Make sure electric strip comes out with screen.

    Aggiungi Commento

    • Remove the two screws securing the electric strip casing on the back of the camera.

    Aggiungi Commento

    • Flip the camera over so that the top is facing you. This is the side with the main button.

    • Remove screws securing the electric strip casing near the speaker

    Aggiungi Commento

    • Flip the camera over so that the back is facing you. This is the side where the LCD screen used to be.

    • Pull the end of the electric strip off of the back of the camera with tweezers.

    Aggiungi Commento

    • Pull the electric strip off of the top of the camera with tweezers.

    • By now, you should have two ends of the electric strip detached from the camera.

    Aggiungi Commento

    • Using your fingers, fully detach the strip along with the casing. This should come off easily. Be careful not to rip or tear any of the electric strip.

    • The black wire should not be broken or removed. This will damage the camera.

    Aggiungi Commento

    • Orient the camera so that you are looking at the back of the camera. This is right above where the LCD screen used to be.

    • Detach the clip of the viewfinder cover with the tweezers.

    • Push up and remove the viewfinder cover.

    Aggiungi Commento

    • Remove the viewfinder mirror by pulling up on the mirror with tweezers.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Nick Oleskowicz

Membro da: 03/04/2012

236 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 15-13, Forte Spring 2012 Membro di Cal Poly, Team 15-13, Forte Spring 2012

CPSU-FORTE-S12S15G13

5 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 15

Tutti i Tempi: 2,507