Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

USB/Auxiliary Port

Cosa ti serve

  1. USB/Auxiliary Port, Outer Case: passo 1, immagine 1 di 2 USB/Auxiliary Port, Outer Case: passo 1, immagine 2 di 2
    • Using the standard metal spudger, begin by prying at the bottom of the plain rubber end cap (the end without the USB or auxiliary input).

  2. USB/Auxiliary Port: passo 2, immagine 1 di 1
    • Continue prying around the end panel, prying at different points until the entire panel is out of its seating.

    • Carefully remove the end panel.

    • The tabs which connect the panel are on the short sides.

    • WARNING: you will likely cause cosmetic damage to the end cap.

  3. USB/Auxiliary Port: passo 3, immagine 1 di 1
    • Slide out the rubber foot located on the bottom of the case.

  4. USB/Auxiliary Port: passo 4, immagine 1 di 1
    • Using a T6 bit, remove the flat topped 5mm screw located on the bottom of the casing, underneath the rubber foot.

    • This is the only flat topped screw in the speaker, so keep track of which one it is.

  5. USB/Auxiliary Port: passo 5, immagine 1 di 3 USB/Auxiliary Port: passo 5, immagine 2 di 3 USB/Auxiliary Port: passo 5, immagine 3 di 3
    • Push against the side without end cap to slide the internal components out of the case.

    • While holding the metal outset casing with one hand, press on the black inner plastic casing with your thumb.

    • It will be very difficult the first time. There is a rubber seal on the outside of the plastic inner case that creates a lot of friction with the metal outer case.

  6. USB/Auxiliary Port, USB/Auxiliary Port: passo 6, immagine 1 di 2 USB/Auxiliary Port, USB/Auxiliary Port: passo 6, immagine 2 di 2
    • Using the standard metal spudger, carefully pry up the top 2 plastic tabs which hold the exterior button and port cover onto the interior plastic frame.

  7. USB/Auxiliary Port: passo 7, immagine 1 di 1
    • Using the classic metal spudger, pry up the bottom 2 tabs attaching the other side of the button panel.

    • It should come off after prying up the first tab.

  8. USB/Auxiliary Port: passo 8, immagine 1 di 3 USB/Auxiliary Port: passo 8, immagine 2 di 3 USB/Auxiliary Port: passo 8, immagine 3 di 3
    • Carefully lift out the end panel.

    • Unplug both the connection ribbon and the ZIF ribbon using tweezers or your hands.

    • There is a bit of glue to hold the connection ribbon down.

  9. USB/Auxiliary Port: passo 9, immagine 1 di 1
    • Remove the 5mm T6 screw holding the port assembly onto the end cap.

    • Unlike the flat top screw holding the metal housing, these screws are roundtop.

  10. USB/Auxiliary Port: passo 10, immagine 1 di 1
    • Remove the old port assembly from the end cap.

    • Alternate Reassembly required, read on.

  11. USB/Auxiliary Port: passo 11, immagine 1 di 1
    • Disconnect the Motherboard connection ribbon from the motherboard.

    • The ribbon should no longer be connected at either end.

  12. USB/Auxiliary Port: passo 12, immagine 1 di 1
    • Very carefully pull the motherboard connection ribbon through the plastic casing, removing it from the plastic casing.

  13. USB/Auxiliary Port: passo 13, immagine 1 di 1
    • Insert the connection ribbon into its ZIF connection port on the bottom of the new port assembly

    • ZIF connectors are delicate and often give beginners trouble, search for ZIF connector tips on the web.

  14. USB/Auxiliary Port: passo 14, immagine 1 di 2 USB/Auxiliary Port: passo 14, immagine 2 di 2
    • Position the new port assembly on the end cap and reinsert the 5mm T6 screw.

    • The rubber insulation around the motherboard connector should help hold the ZIF connector in place after the screw has been reinserted.

  15. USB/Auxiliary Port: passo 15, immagine 1 di 2 USB/Auxiliary Port: passo 15, immagine 2 di 2
    • Reconnect the button ribbon connector on the top of the port assembly.

  16. USB/Auxiliary Port: passo 16, immagine 1 di 2 USB/Auxiliary Port: passo 16, immagine 2 di 2
    • Reconnect the endcap to the plastic housing.

    • While you reconnect the endcap to the plastic housing, carefully position the ribbon slide through the ribbon slit and into the plastic casing.

  17. USB/Auxiliary Port: passo 17, immagine 1 di 1
    • Snap the end cap back onto the inner plastic casing and reconnect the ZIF ribbon to the motherboard.

    • Finish reassembling in descending order starting at step 5.

Conclusione

To reassemble your device, follow steps 1 through 5 in reverse order.

Altre 5 persone hanno completato questa guida.

Noah Sadler

Membro da: 04/01/15

548 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 12-1, Lancaster Spring 2015 Membro di Cal Poly, Team 12-1, Lancaster Spring 2015

CPSU-LANCASTER-S15S12G1

5 Membri

11 Guide realizzate

Un commento

Can anyone at all tell us where we can definitely purchase the USB/Auxiliary Port and its Motherboard to Aux Port ZIF Ribbon?

Thanks in advance.

barrysum - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 12

Tutti i Tempi: 14,956