Aggiusta la tua roba Comunità Store

Spin Master Hatchimal Draggle Nose Replacement

Introduzione

This guide will demonstrate how to properly replace the nose spring for the Hatchimal Draggle. The nose spring can be accessed by first removing the wings and fur .

Cosa ti serve

  1. Spin Master Hatchimal Draggle Nose Replacement, Plastic Wing Replacement: passo 1, immagine 1 di 1

    • lay the Hatchimal on its side.

    Traduci

  2. Spin Master Hatchimal Draggle Nose Replacement: passo 2, immagine 1 di 1

    • Using the plastic opening tool, push in on the purple clip.

    Traduci

  3. Spin Master Hatchimal Draggle Nose Replacement: passo 3, immagine 1 di 1

    • Pull the wing off of the hatchimal.

    • The wing should come off with little resistance.

    Traduci

  4. Spin Master Hatchimal Draggle Nose Replacement, Fur Replacement: passo 4, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement, Fur Replacement: passo 4, immagine 2 di 2

    • Cut the fur retaining zip-tie with a pair of scissors.

    Traduci

  5. Spin Master Hatchimal Draggle Nose Replacement: passo 5, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement: passo 5, immagine 2 di 2

    • Lift the fur up until it can't go further.

    Traduci

  7. Spin Master Hatchimal Draggle Nose Replacement: passo 6, immagine 1 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 6, immagine 2 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 6, immagine 3 di 3

    • Use the spudger tool to push up on the black clip to free it.

    • Pull the clip out.

    Traduci

  8. Spin Master Hatchimal Draggle Nose Replacement: passo 7, immagine 1 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 7, immagine 2 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 7, immagine 3 di 3

    • Lift fur up to reveal the next set of clips.

    • Insert a spudger to push up on the black clip to free it.

    • Pull out the clip.

    Traduci

  9. Spin Master Hatchimal Draggle Nose Replacement: passo 8, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement: passo 8, immagine 2 di 2

    • Lift the fur up and over the Hatchimals Head.

    • Remove the six 12mm Phillips #00 screws from then body.

    Traduci

  10. Spin Master Hatchimal Draggle Nose Replacement: passo 9, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement: passo 9, immagine 2 di 2

    • Pull the casing apart.

    • Remove the yellow speaker cable.

    Traduci

  11. Spin Master Hatchimal Draggle Nose Replacement: passo 10, immagine 1 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 10, immagine 2 di 3 Spin Master Hatchimal Draggle Nose Replacement: passo 10, immagine 3 di 3

    • Remove the three 7mm Phillips #00 screws from the head.

    • Remove the wheel base and the circuit board carefully not to damage the spring.

    Traduci

  12. Spin Master Hatchimal Draggle Nose Replacement: passo 11, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement: passo 11, immagine 2 di 2

    • Push the six black fur clips out using the spudger.

    • Remove the fur completely.

    Traduci

  13. Spin Master Hatchimal Draggle Nose Replacement, Nose Spring Replacement: passo 12, immagine 1 di 2 Spin Master Hatchimal Draggle Nose Replacement, Nose Spring Replacement: passo 12, immagine 2 di 2

    • Using the angled tweezers tool, disconnect the spring that is attached to the nose from the lever.

    Traduci

  14. Spin Master Hatchimal Draggle Nose Replacement: passo 13, immagine 1 di 1

    • Separate the body casing from the core and circuit board.

    • Don't damage the small wire connected from the top of the head to the circuit board.

    Traduci

  15. Spin Master Hatchimal Draggle Nose Replacement: passo 14, immagine 1 di 1

    • Remove a single 7mm Phillips #00 screw from the break.

    • Remove the spring.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Hector Lopez

Membro da: 02/14/18

251 Reputazione

2 Guide realizzate

Distintivi: 4

+ 1 altro distintivo

Team

USF Tampa, Team S1-G5, Nance Spring 2018 Membro di USF Tampa, Team S1-G5, Nance Spring 2018

USFT-NANCE-S18S1G5

3 Membri

10 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 495