Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • Open the small cover on the bottom of the rear cover.

    • Peel back the sticker under the cover to reveal two screws.

    • Remove the two JIS #00 screws from the back of the phone.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 1
    • Remove the six screws from the phone using a JIS #00 screwdriver.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 1
    • Use a nylon spudger to disconnect the seven connectors.

    • Never use a metal spudger around the battery. Use plastic or nylon prying tools instead.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 1
    • The last connector is located under the back sticker.

    • Peel the sticker back to get access of the connector and use a nylon spudger to disconnect it.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 1
    • Remove the camera assembly using an opening tool or spudger.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 1
    • Remove the motherboard with an opening tool or spudger.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Remove the battery with a plastic opening tool or spudger.

    • The battery has adhesive tape that connects it to the phone which makes it difficult to pry out.

    • Never use metal prying tools on the battery. Be sure to use a plastic prying tool to avoid puncturing the battery.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 1
    • Detach the plastic covering from the top side of the phone by hand.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 1
    • Pry off the signal receptor and front camera using an opening tool or spudger.

    • The signal receptor has adhesive tape underneath so proceed with caution when prying.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • Remove the volume and power button with an opening tool or spudger.

    • For replacement, this component comes as a whole. If the volume and power button do not work, they will need to be replaced together.

Linea Traguardo

Un'altra persona ha completato questa guida.

Liam Kanaley

Membro da: 11/03/15

433 Reputazione

3 Guide realizzate

Team

UMass Dartmouth, Team 1-7, Bhusal Fall 2015 Membro di UMass Dartmouth, Team 1-7, Bhusal Fall 2015

UMASSD-BHUSAL-F15S1G7

3 Membri

3 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 8

Tutti i Tempi: 2,053