Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

Use this guide to remove the rear glass of the Sony Xperia Z4.

Opening the Sony Xperia Z4 will damage the waterproof seals on the device. If you do not replace the adhesive seals, your phone will function normally but will lose its water protection.

You’ll need replacement adhesive to reattach components when reassembling the device.

  1. Before you begin, switch off your phone.
    • Before you begin, switch off your phone.

    • Apply a heated iOpener to the back of the phone to loosen the adhesive beneath the back cover. Apply the iOpener for at least two minutes.

  2. Secure a suction handle to the bottom of the back cover, as close to the edge as possible. Lift the back cover with the suction handle to create a small gap between the cover and the frame. Insert an opening pick into the gap.
    • Secure a suction handle to the bottom of the back cover, as close to the edge as possible.

    • Lift the back cover with the suction handle to create a small gap between the cover and the frame.

    • Insert an opening pick into the gap.

    • If you have trouble, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

    • Slide the opening pick to the bottom left corner.

  3. Insert a second opening pick and slide it to the bottom right corner  to cut the adhesive. Leave the opening picks in place to prevent the adhesive from resealing.
    • Insert a second opening pick and slide it to the bottom right corner to cut the adhesive.

    • Leave the opening picks in place to prevent the adhesive from resealing.

  4. Insert a third opening pick at the bottom left corner. In the next few steps whilst cutting around the rear camera make sure you only use the tip of the opening pick to avoid smearing the lens or damaging the camera. Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.
    • Insert a third opening pick at the bottom left corner.

    • In the next few steps whilst cutting around the rear camera make sure you only use the tip of the opening pick to avoid smearing the lens or damaging the camera.

    • Start to slide the tip of the opening pick from the bottom left corner along the side of the phone to cut the adhesive.

    • Leave the opening pick in its place at the top left corner to prevent the adhesive from resealing.

  5. If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it. Insert a fourth opening pick under the top left corner of the back cover.
    • If the adhesive becomes hard to cut it most likely cooled down. Use your iOpener to reheat it.

    • Insert a fourth opening pick under the top left corner of the back cover.

    • Slide the opening pick along the top edge of the phone to cut the adhesive.

    • Leave the opening pick in the top right corner to prevent the adhesive from resealing.

  6. Insert a fifth opening pick at the top right corner of the phone. Slide the opening pick along the right side to cut the remaining adhesive.
    • Insert a fifth opening pick at the top right corner of the phone.

    • Slide the opening pick along the right side to cut the remaining adhesive.

  7. Lift and remove the back cover. After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
    • Lift and remove the back cover.

    • After installing the back cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.

Conclusione

Secure the new back cover with pre-cut adhesive or double-sided adhesive tape after cleaning the according areas with isopropyl alcohol (+90%).

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Dominik Schnabelrauch

Membro da: 23/11/2016

69.373 Reputazione

312 Guide realizzate

Team

iFixit Membro di iFixit

Community

129 Membri

12.616 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 26

Tutti i Tempi: 291