Aggiusta la tua roba Comunità Store

Sony Reader Touch Edition PRS-600 Motherboard Replacement

Cosa ti serve

  1. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Back Panel: passo 1, immagine 1 di 1

    • Using the Phillips head screwdriver PH000, remove the two 1.4 mm screws that are located on the backside of the device.

    Modifica

  2. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 2, immagine 1 di 1

    • Slide the back cover off by pushing it to the left, away from the side that held the screws.

    • Remove the cover.

    Modifica

  3. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 3, immagine 1 di 1

    • This is what the device should look like once the back cover panel has been removed.

    Modifica

  4. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Battery: passo 4, immagine 1 di 1

    • Once the back cover has been removed locate the battery in the bottom right corner of the device.

    • Using the pointed end of the spudger, push out the white plug that is connected to the battery from its beige base.

    Modifica

  6. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 5, immagine 1 di 1

    • Use the flat end of the spudger to pry the battery out of its holder. There may be glue holding it in place.

    Modifica

  7. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Inner Casing: passo 6, immagine 1 di 1

    • Using a screwdriver remove the four 1.4 mm screws that are holding the black plastic casing in place.

    Modifica

  8. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 7, immagine 1 di 1

    • Pry open the black casing to access the screw that is holding down the battery holder.

    • Remove the one 1.4 mm screw that is holding down the battery holder located under black casing.

    • Lift the black inner casing and the battery holder out of the device.

    • The battery holder and the black inner casing are connected by a thin strip of copper. There may be glue holding the black inner casing in place.

    Modifica

  9. Sony Reader Touch Edition PRS-600 Motherboard Replacement, Motherboard: passo 8, immagine 1 di 1

    • Using a Phillips head screwdriver, remove the one 1.4 mm screw holding in the motherboard.

    Modifica

  10. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 9, immagine 1 di 2 Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 9, immagine 2 di 2

    • Using the flat end of the spudger, flip up the 4 latches holding down the thin, orange strips that connect the motherboard to the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports.

    • To disconnect the the screen, audio/AC adapter/micro USB ports, and SD card/PRODuo ports pull each orange slip away from their corresponding latch.

    Modifica

  11. Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 10, immagine 1 di 2 Sony Reader Touch Edition PRS-600 Motherboard Replacement: passo 10, immagine 2 di 2

    • Lift the end of the motherboard closest to the memory cards and pull out.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Terrika Ngobili

Membro da: 10/13/14

857 Reputazione

7 Guide realizzate

Distintivi: 11

+8 altri distintivi

Team

Clemson, Team 1-4, Benson Fall 2014 Membro di Clemson, Team 1-4, Benson Fall 2014

CLEM-BENSON-F14S1G4

4 Membri

22 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 24

Tutti i Tempi: 636