Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Sony Cyber-shot DSC-P52 Shutter Motor Replacement

Cosa ti serve

  1. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Outer Case: passo 1, immagine 1 di 1
    • Open the battery compartment and remove the batteries.

    • Remove all of the visible screws on the outside of the case.

    • There should be three of them that are all easily located.

  2. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 2, immagine 1 di 1
    • Open the memory card compartment.

    • Remove the screw next to the memory card slot.

  3. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 3, immagine 1 di 1
    • Pull apart the front and back cover pieces carefully.

    • The front cover should come completely free with little effort.

    • The back cover will still be attached to the circuit board.

  4. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 4, immagine 1 di 1
    • Simultaneously unclip all of the clips holding in the circuitry. Remove the back case.

    • The circuitry will still be connected to the back case by ribbon cables.

  5. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 5, immagine 1 di 1
    • Open the case as shown.

  6. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 6, immagine 1 di 1
    • Unclip the clip holding the ribbon cable in.

    • Other ribbon cables might not have a clips.

  7. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 7, immagine 1 di 1
    • Pull the ribbon cable out.

  8. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Motherboard Assembly: passo 8, immagine 1 di 1
    • Remove all six screws on the front side of the motherboard circled in the picture.

    • Pull the motherboard from the rest of the housing.

    • It will still be connected to the flash unit.

  9. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 9, immagine 1 di 1
    • Remove the cable on the back side of the motherboard.

  10. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 10, immagine 1 di 1
    • Detach the ribbon cables shown.

    • Careful! Touching the leads of the large yellow capacitor can result in a painful shock.

    • Remove the flash unit from the motherboard.

  11. Sony Cyber-shot DSC-P52 Shutter Motor Replacement, Shutter Motor: passo 11, immagine 1 di 1
    • Remove screw securing motor and mount in place.

    • Be careful to leave shutter gears in the correct position

  12. Sony Cyber-shot DSC-P52 Shutter Motor Replacement: passo 12, immagine 1 di 1
    • Remove the two screws holding motor to mount/gears.

    • Remove the motor from the mount.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Team

Cal Poly, Team 3-43, Regan Winter 2011 Membro di Cal Poly, Team 3-43, Regan Winter 2011

CPSU-REGAN-W11S3G43

4 Membri

20 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 46

Tutti i Tempi: 4,902