Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the device so the bottom is facing up, and the lens is facing you ("bottom view").
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove these two black M1.4 X 3.5 Phillips head screws.
-
The third, unmarked screw does not need to be removed at this time.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the device so the LCD is facing you, and the hdmi cover is facing up ("left view).
-
Remove these three black M1.4 X 3.5 Phillips head screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the device with the Wifi/GPS logo facing up ("right view").
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a prying motion and a plastic opening tool to pry the side panel up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
After removing the panel, remove the two black M1.4 X 3.5 Phillips head screws.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the device so that the LCD is facing you ("back view").
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the plastic opening tool with a prying motion, going between the case and the LCD, from the middle of the LCD to the right of the device, undoing the claws retaining the back.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unhook the small printed circuit board by gently pressing the board towards the top of the device and lifting up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a plastic opening tool remove the black LCD retainer clip to the right of LCD.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the plastic opening tool to gently lift the LCD from the device
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the plastic opening tool to lift the black retaining clip up to disengage the ribbon cable. Then gently pull the ribbon cable to remove.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the black M1.4 X 3.5 Phillips head screw in upper right corner of the device.
-
Service manual for reference: Click to go to the service manual.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Reorient the camera so you are looking at the "top view".
-
Remove the black M1.4 X 3.5 Phillips head screw next to the ON/OFF button circled in red.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Orient the device so you are looking at the "bottom view".
-
Remove the black M1.4 X 3.5 Phillps head screw located next to the tripod attachment.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The connections (red squares) have small black retaining clips. Using a plastic opening tool, lift upward towards the cable to unlock.
-
The upper ribbon cable simply pulls loose.
-
Annulla: non ho completato questa guida.
Altre 11 persone hanno completato questa guida.
7 Commenti
Can you tell me how to open Sony hx20v lens..... I have problem in my Sony camera n I don't know how to fix the lens I try several times but I'm so worried about to break any part or wrong fix. Please show how to open lens (only lens) part.....please..sorryforbadenglish.
These guides are best suited if you are replacing parts. There's no 'repairing' the individual components. If you can find another broken camera of the same model (but with a good lens) then you could replace it.
can i follow the same instruction for SONY DSC HX 10V .as both looks identical . when i shake my camera sound comes as if some parts are loosen but when i switched on my camera and the lens comes out that sound goes off . should i care for it or not ?
I followed all the steps and I was able to fix a problem with the lens. Thanks a lot! ! ++
I have successfully changed with the help of your description my noisy lense system
thanks a lot
D. A. Waldvogel