Aggiusta la tua roba

Diritto alla Riparazione

Store

Shark Vacuum Pet Hair Power Brush Roller Replacement

Scritto Da: Roshni Sachar (e 4 altri collaboratori)
  • Commenti: 11
  • Preferiti: 1
  • Completamenti: 3

Difficoltà

Moderato

Passi

5

Tempo Necessario

10 - 20 minuti

Sezioni

1

Contrassegni

1

Step Trimmer

Tagliatore di Passi

Questa guida contiene passaggi inutili. Tagliali, sii più conciso!

Introduzione

Many vacuum cleaners have a separate pet hair and power brush head. The roller brush of the head can easily break due to wear and tear. Use this guide to replace the internal roller brush in the power brush head of your Shark vacuum cleaner.

  1. This Shark model brush head consists of 7 parts: a base frame, a gear, a roller brush, two side screws, a plastic round band, and a top frame of the head. Push the grey button on the back panel to open up the brush head.

    • This Shark model brush head consists of 7 parts: a base frame, a gear, a roller brush, two side screws, a plastic round band, and a top frame of the head.

    • Push the grey button on the back panel to open up the brush head.

    Traduci

  2. Take the purple gear out of the brush head body. Take the purple gear out of the brush head body.

    • Take the purple gear out of the brush head body.

    Traduci

  4. Pull out the roller brush from the brush head. Take out the black plastic band.

    • Pull out the roller brush from the brush head.

    • Take out the black plastic band.

    • The black band is an important component and will be needed for reassembly so keep it carefully.

    Traduci

  5. Pull out the side screws from the right and left side of the roller brush.

    • Pull out the side screws from the right and left side of the roller brush.

    • There are two screws, one on each side.

    Traduci

  6. Take the new roller brush and fit the two grey screws/fittings on either side of the roller brush until they are secure. Take the new roller brush and fit the two grey screws/fittings on either side of the roller brush until they are secure. Take the new roller brush and fit the two grey screws/fittings on either side of the roller brush until they are secure.

    • Take the new roller brush and fit the two grey screws/fittings on either side of the roller brush until they are secure.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Roshni Sachar

Membro da: 19/03/2016

184 Reputazione

1 Guida realizzata

Distintivi: 7

+4 altri distintivi

Team

Michigan Tech, Team 1-23, Lauer Spring 2016 Membro di Michigan Tech, Team 1-23, Lauer Spring 2016

MTU-LAUER-S16S1G23

1 Membro

1 Guida realizzata

5 Commenti

Aggiungi un commento

Cat hair will jam up in the small gap between the gear and the bushing on the turbine and will cause enough friction to stop the turbine. I used a needle to dig out the hair and it solved the problem.

hvabrams - Replica

very clear and concise. took me 5 minutes with your instructions - couldn’t find anything like this on the shark site.

tigersfoot - Replica

I need to put back all parts , don’t know where to start, can u explain step by step how to put them back please . Thank you

paolodigiacomo23 - Replica

Where can I purchase one of the side screw/fittings?

Renee Mills - Replica

Thank you to the first person who commented on the cat hair. I also took a needle to the area suggested , “It works”!

Vivienne Forsythe - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 6

Ultimi 7 Giorni: 96

Ultimi 30 Giorni: 595

Tutti i Tempi: 26,500