Aggiusta la tua roba Comunità Store

Shark Ultimate Professional Heat Plate Replacement

Introduzione

This guide will show you how to replace the heat plate of your Shark Ultimate Professional clothes iron. If your heat plate is damaged or worn out, it may affect the iron's performance and cause problems with your clothes. Some signs of a faulty heat plate are as follows.

-Uneven heating or cold spots

-low steam output or lack of steam

-stains on clothes

-corrosion on heat plate

If any of these signs are occuring, you may need to replace the heat plate with a new one. To do this you will simply need a phillips screwdriver and a new heat plate. Now before starting make sure that the iron is unpluged and cooled down . By following this guide you will be able to fix your Shark Ultimate Professional Clothes Iron.

Cosa ti serve

  1. Shark Ultimate Professional Heat Plate Replacement, Heat Plate: passo 1, immagine 1 di 3 Shark Ultimate Professional Heat Plate Replacement, Heat Plate: passo 1, immagine 2 di 3 Shark Ultimate Professional Heat Plate Replacement, Heat Plate: passo 1, immagine 3 di 3

    • Remove the two screws at the back of the iron.

    • Remove the back cover piece.

    • Make sure iron is unplugged and cooled off.

    Traduci

  2. Shark Ultimate Professional Heat Plate Replacement: passo 2, immagine 1 di 2 Shark Ultimate Professional Heat Plate Replacement: passo 2, immagine 2 di 2

    • Remove the two screws holding the white clamp to the iron.

    • Remove the two screws holding the black wires to the body of the iron.

    • Removing the left black wire will also free the red wire, attached by the same screw.

    Traduci

  3. Shark Ultimate Professional Heat Plate Replacement: passo 3, immagine 1 di 1

    • Pull the split end of the power cord upward through the ball joint of the iron.

    • Set aside power cord.

    Traduci

  4. Shark Ultimate Professional Heat Plate Replacement: passo 4, immagine 1 di 3 Shark Ultimate Professional Heat Plate Replacement: passo 4, immagine 2 di 3 Shark Ultimate Professional Heat Plate Replacement: passo 4, immagine 3 di 3

    • Remove remaining screws that hold a wire on the bottom (brown and blue).

    • Unscrew from left to right.

    • Unclip the black adapter piece on the bottom right.

    • Wires order (from left to right): Brown, Blue, Red, Black

    Traduci

  5. Shark Ultimate Professional Heat Plate Replacement: passo 5, immagine 1 di 2 Shark Ultimate Professional Heat Plate Replacement: passo 5, immagine 2 di 2

    • Remove two screws (left and right) affixed to circuit board.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Autore

con 6 altri collaboratori

Drew Carff

Membro da: 10/23/17

868 Reputazione

5 Guide realizzate

Distintivi: 14

+11 altri distintivi

Team

USF Tampa, Team S1-G4, Leahy Fall 2017 Membro di USF Tampa, Team S1-G4, Leahy Fall 2017

USFT-LEAHY-F17S1G4

3 Membri

10 Guide realizzate

3 Commenti

This is an incomplete guide. Why even put it up. So silly and ridiculous. Not Good at all.

Muhammad Ahmad - Replica

Where is the part about the heat plate?

Nealy Moxam - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 21

Tutti i Tempi: 2,166