Aggiusta la tua roba Comunità Store

Shark Ultimate Professional Circuit Board Replacement

Introduzione

Before beginning this guide, ensure that the device is both unplugged and cool; failure to do so may result in electrocution or burns.

Cosa ti serve

  1. Shark Ultimate Professional Circuit Board Replacement, Circuit Board: passo 1, immagine 1 di 3 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: passo 1, immagine 2 di 3 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: passo 1, immagine 3 di 3

    • Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron.

    • Remove the back cover piece.

    • Make sure the iron is unplugged and cooled off.

    Modifica

  2. Shark Ultimate Professional Circuit Board Replacement: passo 2, immagine 1 di 2 Shark Ultimate Professional Circuit Board Replacement: passo 2, immagine 2 di 2

    • Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron.

    • Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.

    • Removing the left black wire will also free the red wire, attached by the same screw.

    Modifica

  3. Shark Ultimate Professional Circuit Board Replacement: passo 3, immagine 1 di 1

    • Pull the split end of the power cord upward through the ball joint.

    • Set aside the power cord.

    Modifica

  5. Shark Ultimate Professional Circuit Board Replacement: passo 4, immagine 1 di 3 Shark Ultimate Professional Circuit Board Replacement: passo 4, immagine 2 di 3 Shark Ultimate Professional Circuit Board Replacement: passo 4, immagine 3 di 3

    • Use the Philips head #0 screwdriver to remove the remaining 6.58mm screws that hold the wires on the bottom (brown and blue).

    • Remove from left to right

    • Unclip the black adapter piece on the bottom right.

    • Wires order (from left to right): Brown, Blue, Red, Black

    Modifica

  6. Shark Ultimate Professional Circuit Board Replacement: passo 5, immagine 1 di 2 Shark Ultimate Professional Circuit Board Replacement: passo 5, immagine 2 di 2

    • Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board.

    Modifica

  7. Shark Ultimate Professional Circuit Board Replacement: passo 6, immagine 1 di 2 Shark Ultimate Professional Circuit Board Replacement: passo 6, immagine 2 di 2

    • Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board.

    • Gently pull the circuit board from affixed position.

    • The circuit board will not be completely separated at this point.

    Modifica

  8. Shark Ultimate Professional Circuit Board Replacement: passo 7, immagine 1 di 3 Shark Ultimate Professional Circuit Board Replacement: passo 7, immagine 2 di 3 Shark Ultimate Professional Circuit Board Replacement: passo 7, immagine 3 di 3

    • Remove the mode display piece and set aside.

    • Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.

    Modifica

  9. Shark Ultimate Professional Circuit Board Replacement: passo 8, immagine 1 di 1

    • Remove the connecting wire from the connected adapter in the handle by pulling lightly.

    • Set aside the circuit board.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 5 altri collaboratori

Drew Carff

Membro da: 10/23/17

868 Reputazione

5 Guide realizzate

Distintivi: 14

+11 altri distintivi

Team

USF Tampa, Team S1-G4, Leahy Fall 2017 Membro di USF Tampa, Team S1-G4, Leahy Fall 2017

USFT-LEAHY-F17S1G4

3 Membri

10 Guide realizzate

4 Commenti

My shark 1505C does not have philips screws on the back. They are security torx and I cannot find a tool to open it.

Where can I buy a main board for this iron ?

Thanks

NevG.

nevstarg - Replica

where do I buy it's circuit board?

egovieira - Replica

Where can u buy the circuit board professional 1800 version?

Astinder Singhera - Replica

How much does the circuit board cost? and where can i purchase it?

D.A. Willis - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 29

Tutti i Tempi: 3,068