Aggiusta la tua roba Comunità Store

Sceptre X9 Komodo VII Power Supply Unit Replacement

Introduzione

Use this guide to remove the power supply unit.

Cosa ti serve

  1. Sceptre X9 Komodo VII Power Supply Unit Replacement, Stand: passo 1, immagine 1 di 1

    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

    Traduci

  2. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 2, immagine 1 di 1

    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

    Traduci

  3. Sceptre X9 Komodo VII Power Supply Unit Replacement, Board Cover: passo 3, immagine 1 di 1

    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

    Traduci

  5. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 4, immagine 1 di 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 4, immagine 2 di 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 4, immagine 3 di 3

    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

    Traduci

  6. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 5, immagine 1 di 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 5, immagine 2 di 2

    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

    Traduci

  7. Sceptre X9 Komodo VII Power Supply Unit Replacement, Power Supply Unit: passo 6, immagine 1 di 1

    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

    Traduci

  8. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 7, immagine 1 di 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 7, immagine 2 di 3 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 7, immagine 3 di 3

    • Unplug the seven connections from the power supply unit by gently pulling on them.

    Traduci

  9. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 8, immagine 1 di 1

    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

    Traduci

  10. Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 9, immagine 1 di 2 Sceptre X9 Komodo VII Power Supply Unit Replacement: passo 9, immagine 2 di 2

    • Lift the power supply unit straight up to remove it from the back panel.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Jose Carrillo

Membro da: 09/26/12

23 Reputazione

1 Guida realizzata

Distintivi: 6

+3 altri distintivi

Team

Cal Poly, Team 16-56, Forte Fall 2012 Membro di Cal Poly, Team 16-56, Forte Fall 2012

CPSU-FORTE-F12S16G56

5 Membri

13 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 664