Samsung NX Mini Flash Assembly Replacement

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Introduzione

This guide will show you how to remove the flash assembly in the Samsung NX Mini. The flash assembly includes the capacitor, so be sure to discharge the capacitor prior to removal. Learn more about discharging capacitors here.

Cosa ti serve

Passo 1 Battery

Samsung NX Mini Flash Assembly Replacement, Battery: passo 1, immagine 1 di 3

Samsung NX Mini Flash Assembly Replacement, Battery: passo 1, immagine 2 di 3

Samsung NX Mini Flash Assembly Replacement, Battery: passo 1, immagine 3 di 3

Orient the camera so the button panel and LCD are facing you.
Use a spudger or fingernail to open the battery compartment on the right side of the camera.

Traduci

Passo 2

Push the blue trapdoor to the left to release the battery, and remove the battery.
There is no battery shown in this photo.

Traduci

Passo 3 Front Case

Samsung NX Mini Flash Assembly Replacement, Front Case: passo 3, immagine 1 di 1

Use a Phillips #00 screwdriver to remove the 4 mm screw inside the battery compartment.

Traduci

Passo 4

Remove the 4 mm Phillips #00 screw hiding in the external flash port.

Traduci

Passo 5

Remove the four 5 mm Phillips #00 screws from the lens assembly.

Traduci

Passo 6

Remove the metal lens mount by hand or with tweezers.
Be careful not to touch the sensor in the center of the lens assembly.

Traduci

Passo 7

Use tweezers to remove the inner metal ring.

Traduci

Passo 8

Use a Phillips #00 screwdriver to remove the three 4 mm screws from the bottom of the case.

Traduci

Passo 9

Use your hands to slowly pull the front casing away from the camera.
The case is attached with multiple clips that may make a cracking noise as you pull it away from the camera.

Traduci

Passo 10 Sensor

Samsung NX Mini Flash Assembly Replacement, Sensor: passo 10, immagine 1 di 3

Samsung NX Mini Flash Assembly Replacement, Sensor: passo 10, immagine 2 di 3

Samsung NX Mini Flash Assembly Replacement, Sensor: passo 10, immagine 3 di 3

Gently flip the sensor cover back to expose the screw attaching the sensor cover to the ribbon cable.
Use a Phillips #00 screwdriver to remove the 3 mm screw from the sensor cover.
Use tweezers to remove the metal contact cover. Be sure to carefully remove the cover so the gold contacts remain in place.
The gold lens contacts lying beneath the ribbon cable become loose when the screw and contact cover are removed.

Traduci

Passo 11

Remove the four 4 mm Phillips #00 screws holding the sensor mount in place.

Traduci

Passo 12

Samsung NX Mini Flash Assembly Replacement: passo 12, immagine 3 di 3

Remove the four 4 mm Phillips #00 screws securing the battery compartment to the mother board.
Remove the battery compartment.

Traduci

Passo 13

Use a spudger to disconnect the ribbon cable connecting the image sensor to the motherboard.

Traduci

Passo 14

Gently remove the sensor mount from the camera case.

Traduci

Passo 15 Motherboard

Samsung NX Mini Flash Assembly Replacement, Motherboard: passo 15, immagine 1 di 2

Samsung NX Mini Flash Assembly Replacement, Motherboard: passo 15, immagine 2 di 2

Use a Phillips #00 screwdriver to remove the 3 mm screw located below the wifi antenna.

Traduci

Passo 16

Use tweezers to disconnect the wifi antenna from the motherboard.

Traduci

Passo 17

Samsung NX Mini Flash Assembly Replacement: passo 17, immagine 3 di 3

Use a spudger to disconnect the LCD ribbon cable by prying it straight up from the motherboard.

Traduci

Passo 18

Samsung NX Mini Flash Assembly Replacement: passo 18, immagine 3 di 3

Use a spudger to unlock the topmost ZIF connector by flipping open the black flap.

Traduci

Passo 19

Insert the pointed end of a spudger into the hole in the middle of the ribbon cable.
Gently pull the spudger back to slide the ribbon cable out of its connector.

Traduci

Passo 20

Samsung NX Mini Flash Assembly Replacement: passo 20, immagine 3 di 3

Disconnect the blue ribbon cable from the motherboard.
Insert the pointed end of a spudger into the hole in the top of the ribbon.
Gently pull the ribbon from the connector.

Traduci

Passo 21

Remove the motherboard from the camera.

Traduci

Passo 22 Flash Assembly

Samsung NX Mini Flash Assembly Replacement, Flash Assembly: passo 22, immagine 1 di 3

Samsung NX Mini Flash Assembly Replacement, Flash Assembly: passo 22, immagine 2 di 3

Samsung NX Mini Flash Assembly Replacement, Flash Assembly: passo 22, immagine 3 di 3

Use a Phillips #00 screwdriver to remove the two 5 mm screws holding the flash assembly to the camera case.

Traduci

Passo 23

Remove the flash assembly by gently pulling it away from the case.
You may need to use a spudger to release some of the clips holding the assembly in place.
Avoid touching the ends of the capacitor (the large black cylinder on the right). Capacitors that haven't been discharged may cause electric shock. Learn how to discharge a capacitor here.