Salta al contenuto principale

Introduzione

A guide to help replace the spring inside of the setting knob on top of the camera.

  1. Samsung L100 Setting Knob Spring, Removing Back Cover: passo 1, immagine 1 di 3 Samsung L100 Setting Knob Spring, Removing Back Cover: passo 1, immagine 2 di 3 Samsung L100 Setting Knob Spring, Removing Back Cover: passo 1, immagine 3 di 3
    • Remove the six external screws from the camera using a Phillips #0 screwdriver.

    • After the screws has been removed, the bottom of the back half of the external case should be loosened from the camera.

    • Be careful, make sure you don't lose the screws.

  2. Samsung L100 Setting Knob Spring: passo 2, immagine 1 di 2 Samsung L100 Setting Knob Spring: passo 2, immagine 2 di 2
    • Open the battery cover that's located on the bottom right side of the camera and carefully remove the battery.

  3. Samsung L100 Setting Knob Spring: passo 3, immagine 1 di 3 Samsung L100 Setting Knob Spring: passo 3, immagine 2 di 3 Samsung L100 Setting Knob Spring: passo 3, immagine 3 di 3
    • Slide your fingernail or a plastic spudger in the groove from the bottom to the top right side of the camera.

  4. Samsung L100 Setting Knob Spring: passo 4, immagine 1 di 1
    • Carefully squeeze the top right corner of the camera and pry off the external cover.

    • If you hear a "cracking" sound. This is normal.

    • Continue to pull the external cover and it will come off cleanly.

    • Be cautious of the flash capacitor. It carries an electrical charge, that may give you an unpleasant shock.

  5. Samsung L100 Setting Knob Spring: passo 5, immagine 1 di 1
    • Carefully pull off the back cover, parts behind the back of the case might fall out.

  6. Samsung L100 Setting Knob Spring, Flash Circuit Board: passo 6, immagine 1 di 1
    • Remove the screws holding the circuit board.

    • After you remove the screws, carefully remove the circuit board.

  7. Samsung L100 Setting Knob Spring: passo 7, immagine 1 di 2 Samsung L100 Setting Knob Spring: passo 7, immagine 2 di 2
    • Remove the front cover, it comes off easily.

    • Buttons might fall out when you remove the front cover.

  8. Samsung L100 Setting Knob Spring: passo 8, immagine 1 di 1
    • Face camera towards you.

    • Remove the two screws from circuit board on the left side of the lens.

  9. Samsung L100 Setting Knob Spring: passo 9, immagine 1 di 1
    • Carefully hold up the circuit board, while it's still connected to the camera.

    • Remove all five screws that's on top of the camera.

  10. Samsung L100 Setting Knob Spring: passo 10, immagine 1 di 3 Samsung L100 Setting Knob Spring: passo 10, immagine 2 di 3 Samsung L100 Setting Knob Spring: passo 10, immagine 3 di 3
    • Carefully push up the top of the circuit board.

    • Pull up flash circuit board from top of camera.

  11. Samsung L100 Setting Knob Spring, Setting Knob Spring: passo 11, immagine 1 di 1
    • Face the bottom of the Flash Circuit board towards you.

    • Remove the one screw that's located on the left side of the lens.

  12. Samsung L100 Setting Knob Spring: passo 12, immagine 1 di 1
    • Take the flash circuit board and turn it over.

    • Remove the plastic setting knob.

    • Make sure to keep copper spring inside of the slot.

  13. Samsung L100 Setting Knob Spring: passo 13, immagine 1 di 3 Samsung L100 Setting Knob Spring: passo 13, immagine 2 di 3 Samsung L100 Setting Knob Spring: passo 13, immagine 3 di 3
    • Take out and replace the Setting Knob Spring with tweezers.

Conclusione

To reassemble your device, follow these instructions in reverse order.

andyhe

Membro da: 15/04/2010

75 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 6-17, Maness Spring 2010 Membro di Cal Poly, Team 6-17, Maness Spring 2010

CPSU-MANESS-S10S6G17

4 Membri

10 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 3,005