Salta al contenuto principale

Samsung Galaxy Watch Motherboard Replacement

Cosa ti serve

  1. Samsung Galaxy Watch Motherboard Replacement, Opening Procedure: passo 1, immagine 1 di 1
    • Remove the four Tri-point #00 screws (4.2 mm length) on the backside of the watch.

  2. Samsung Galaxy Watch Motherboard Replacement: passo 2, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement: passo 2, immagine 2 di 2
    • Use an opening tool to get between the back cover and the metal housing of the watch.

    • Carefully pry the plastic back cover open.

    • Don't remove the back cover yet. There is a flex cable running to the core assembly inside.

  3. Samsung Galaxy Watch Motherboard Replacement: passo 3, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement: passo 3, immagine 2 di 2
    • Lay down the watch and lift the back cover to access the sensor connector on the motherboard.

  4. Samsung Galaxy Watch Motherboard Replacement: passo 4, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement: passo 4, immagine 2 di 2
    • Use a spudger to disconnect the sensor flex cable from the motherboard.

  5. Samsung Galaxy Watch Motherboard Replacement: passo 5, immagine 1 di 3 Samsung Galaxy Watch Motherboard Replacement: passo 5, immagine 2 di 3 Samsung Galaxy Watch Motherboard Replacement: passo 5, immagine 3 di 3
    • Remove the back cover.

    • When closing the watch make sure the rubber gasket is undamaged or replace it with a new one.

  6. Samsung Galaxy Watch Motherboard Replacement, Core Assembly Removal: passo 6, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement, Core Assembly Removal: passo 6, immagine 2 di 2
    • Use a spudger to disconnect the display flex cable from the motherboard.

  7. Samsung Galaxy Watch Motherboard Replacement: passo 7, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement: passo 7, immagine 2 di 2
    • Lift the core unit out of the housing.

    • The core's plastic frame sits tight inside the housing.

    • Carefully thread the display flex cable through the gap of the core's plastic frame.

  8. Samsung Galaxy Watch Motherboard Replacement, Motherboard: passo 8, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement, Motherboard: passo 8, immagine 2 di 2
    • Use a spudger to disconnect the hall sensor flex cable.

  9. Samsung Galaxy Watch Motherboard Replacement: passo 9, immagine 1 di 3 Samsung Galaxy Watch Motherboard Replacement: passo 9, immagine 2 di 3 Samsung Galaxy Watch Motherboard Replacement: passo 9, immagine 3 di 3
    • Use a pair of tweezers to gently peel both button cables from the plastic frame.

  10. Samsung Galaxy Watch Motherboard Replacement: passo 10, immagine 1 di 1
    • Remove the single Phillips #00 screw (3.4 mm length).

  11. Samsung Galaxy Watch Motherboard Replacement: passo 11, immagine 1 di 2 Samsung Galaxy Watch Motherboard Replacement: passo 11, immagine 2 di 2
    • Insert a spudger into the small gap underneath the motherboard where the cutout in the plastic frame is.

    • Lift the motherboard by twisting the spudger.

  12. Samsung Galaxy Watch Motherboard Replacement: passo 12, immagine 1 di 1
    • Remove the motherboard.

Conclusione

If possible, turn on your device and test your repair before resealing.

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

Take your e-waste to an R2 or e-Stewards certified recycler.

Altre 7 persone hanno completato questa guida.

Tobias Isakeit

Membro da: 03/31/14

117.597 Reputazione

188 Guide realizzate

Team

Master Techs Membro di Master Techs

Community

322 Membri

2.531 Guide realizzate

7 Commenti

Anyone know where to purchase a Galaxy Watch mother board?

lorne serpa - Replica

What is the part number, or where can you get the motherboard?

Nick Henthorn - Replica

Where can the motherboard be purchased from for Galaxy Watch ?

Mohammed Aamir - Replica

I got a motherboard on ebay. Including import duties it was something like 90$. Shipped to Denmark.

Definitely cheaper than repair shop and absolutely more fun! :)

Agris Jurjans - Replica

Hello,

Do you know if switching a motherboard from a GW46 Bluetooth only (R800) to a GW46 LTE (R805) is a straight swap or additional parts are needed?

As my R800 sensors are dead and i need to replace the motherboard and the back cover anyway.

Thanks

BRazvy - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 35

Ultimi 30 Giorni: 138

Tutti i Tempi: 11,804