Salta al contenuto principale

Introduzione

If your camera has been damaged or not working properly, use this guide to replace your front-facing camera.

  1. Turn off the tablet before disassembly.
    • Turn off the tablet before disassembly.

    • Heat up an iOpener for 30 seconds and place on all four seams of the screen. A heat gun can be used as well.

  2. The glue is now melted, so using the metal spudger shown,  pry open all sides of the tablet. When prying open near the home and touch screen buttons, use a suction cup.
    • The glue is now melted, so using the metal spudger shown, pry open all sides of the tablet.

    • When prying open near the home and touch screen buttons, use a suction cup.

    • Do not stick the metal spudger past these buttons as this may damage your device.

  3. Carefully lift up the screen. There is a ribbon cable attached. Lifting the screen too quickly can damage the cable.
    • Carefully lift up the screen.

    • There is a ribbon cable attached. Lifting the screen too quickly can damage the cable.

  4. Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora

    Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora
  5. Remove the ribbon cable using the Metal Spudger. The ribbon may be taped underneath to the grey frame. Gently lift the ribbon to untape it. The ribbon may be taped underneath to the grey frame. Gently lift the ribbon to untape it.
    • Remove the ribbon cable using the Metal Spudger.

    • The ribbon may be taped underneath to the grey frame. Gently lift the ribbon to untape it.

  6. Remove all seventeen 3 mm screws using  a PH000 Phillips screwdriver. Remove all seventeen 3 mm screws using  a PH000 Phillips screwdriver.
    • Remove all seventeen 3 mm screws using a PH000 Phillips screwdriver.

  7. Lift the black frame using the two Metal Spudgers shown. On the third picture, there is a Sim Card component that is connected to the frame and back cover. As you lift up the frame, it'll detach. This is normal. On the third picture, there is a Sim Card component that is connected to the frame and back cover. As you lift up the frame, it'll detach. This is normal.
    • Lift the black frame using the two Metal Spudgers shown.

    • On the third picture, there is a Sim Card component that is connected to the frame and back cover. As you lift up the frame, it'll detach. This is normal.

  8. Once lifted, flip the grey frame over.
    • Once lifted, flip the grey frame over.

    • This component connects to the sim card.

    • Remember to click this component back into place when reassembling the tablet.

  9. This is where the front-facing camera is located on  the frame
    • This is where the front-facing camera is located on the frame

  10. Using the Blunt ESD Tweezer, disconnect the front-facing camera Lift the camera Lift the camera
    • Using the Blunt ESD Tweezer, disconnect the front-facing camera

    • Lift the camera

Conclusione

To reassemble your device, follow these instructions in reverse order.

Divya Prabakaran

Membro da: 20/02/2017

633 Reputazione

6 Guide realizzate

Team

USF Tampa, Team S2-G4, Sullivan Spring 2017 Membro di USF Tampa, Team S2-G4, Sullivan Spring 2017

USFT-SULLIVAN-S17S2G4

4 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 1

Tutti i Tempi: 161