Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

If you have a damaged, broken, or corrupted motherboard, this guide will help you replace it.

  1. Have the front of the device facing you. Begin near one of the curved edges of the device (see photo two for visual example).
    • Have the front of the device facing you.

    • Begin near one of the curved edges of the device (see photo two for visual example).

    • Place a plastic opening tool between the front and back panels.

    • If a plastic opening tool doesn’t work, using a metal spudger may work, but it may damage the plastic on the device.

    • Remember to remove the micro SD card (if present) before you begin.

  2. Once the plastic opening tool is fully inserted, wedge it around the device’s edges to separate the panels. Lift the back panel off of the device.
    • Once the plastic opening tool is fully inserted, wedge it around the device’s edges to separate the panels.

    • Lift the back panel off of the device.

    • The back panel will make a clicking noise while being lifted off of the device.

  3. Remove the adhesive film and flip up the retaining flap on the ZIF battery connector.
    • Remove the adhesive film and flip up the retaining flap on the ZIF battery connector.

    • Slide the orange battery ribbon cable out of the ZIF connector.

  4. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  5. Remove the adhesive film, lift the retaining tab and withdraw the white speaker ribbon. Remove the adhesive film, lift the retaining tab and withdraw the white speaker ribbon.
    • Remove the adhesive film, lift the retaining tab and withdraw the white speaker ribbon.

  6. Lift the retaining tab and withdraw the black LCD ribbon. Lift the retaining tab and withdraw the black LCD ribbon. Lift the retaining tab and withdraw the black LCD ribbon.
    • Lift the retaining tab and withdraw the black LCD ribbon.

  7. Using a Phillips #000 screwdriver, remove the ten 4 mm screws around the battery. Slide a plastic opening tool under the bottom of the battery close to the speakers and lift up.
    • Using a Phillips #000 screwdriver, remove the ten 4 mm screws around the battery.

    • Slide a plastic opening tool under the bottom of the battery close to the speakers and lift up.

    • The large rectangular white and black piece is the entire battery. Be careful not to puncture it.

  8. Flip up the two ZIF connectors on the motherboard using the plastic opening tool. Slide the orange ribbon cables out of the ZIF connectors. Remove the front-facing camera.
    • Flip up the two ZIF connectors on the motherboard using the plastic opening tool.

    • Slide the orange ribbon cables out of the ZIF connectors.

    • Remove the front-facing camera.

  9. Disconnect the headphone jack from the motherboard.
    • Disconnect the headphone jack from the motherboard.

    • Use a Phillips # 000 to remove six 4mm screws.

  10. Lodge the plastic opening tool under and lift the motherboard out of the tablet. Be careful not to snag any connectors.
    • Lodge the plastic opening tool under and lift the motherboard out of the tablet.

    • Be careful not to snag any connectors.

    • Remove the metal bracket that was underneath the charging port and set aside.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 6 persone hanno completato questa guida.

Isabella Li

Membro da: 02/10/2017

1.901 Reputazione

7 Guide realizzate

Team

Cal Poly, Team S15-G6, Livingston Fall 2017 Membro di Cal Poly, Team S15-G6, Livingston Fall 2017

CPSU-LIVINGSTON-F17S15G6

4 Membri

21 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 8

Ultimi 7 Giorni: 62

Ultimi 30 Giorni: 324

Tutti i Tempi: 8,437