Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    , Cover Posteriore: passo 1, immagine 1 di 2 , Cover Posteriore: passo 1, immagine 2 di 2
    • The plastic opening tool may break during this step. You may need to use the heavy duty spudger instead.

    • Insert the plastic opening tool between the glass screen and the back cover so the curved end of the plastic opening tool is under the glass. Gently pry the back cover away from the glass screen.

    • Be sure to lift the entire display from the body and that you are not are lifting the glass from the display. You will need to reach down a little further for the correct removal.

    • Continue inserting the plastic opening tool around the whole device screen to completely separate the back cover from the glass screen.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 2 : passo 2, immagine 2 di 2
    • Gently lift the screen up with your finger.

    • If the screen will not separate from the back cover, try repeating step 1.

  3. , Scollegamento Batteria: passo 3, immagine 1 di 1
    • Usando le dita, rimuovi il nastro verde che copre il connettore della batteria.

  4. : passo 4, immagine 1 di 3 : passo 4, immagine 2 di 3 : passo 4, immagine 3 di 3
    • Inserisci la parte piatta dello spudger di plastica tra i cavi e la parte inferiore del connettore della batteria. Facendo attenzione solleva il connettore nero della batteria per scollegarla dalla scheda madre.

    • Lo spudger di metallo mostrato in foto non è consigliato in quanto può provocare cortocircuiti. Usa uno strumento ESD, come lo spudger di nylon.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 2 : passo 5, immagine 2 di 2
    • The charging port cable is the black cable connected to the charger port. Using your fingers, peel the green tape off of the charging port cable connector.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 2 : passo 6, immagine 2 di 2
    • Using the flat end of heavy-duty spudger, carefully lift the black tab that holds the charger port cable in place.

    • Slide the cable out.

    • There is a small strip of adhesive holding the charger port cable to the battery. You may need to slide the heavy-duty spudger between the cable and the battery to slide the cable out.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Use the Phillips 000 screwdriver to unscrew the two 3mm screws holding the charger port in place.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 1
    • Use the flat end of the heavy-duty spudger to lift the white microphone piece until it is removed from its socket.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 3 : passo 9, immagine 2 di 3 : passo 9, immagine 3 di 3
    • Be sure to insert the spudger underneath the charger port and not inside the charger port to avoid damaging the component

    • Slide the flat end of the heavy-duty spudger under the charger port.

    • Make sure the spudger is all the way to the back of the cavity and slide horizontally across the bottom to break the adhesive.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • Lift the charger port with the flat end of the heavy-duty spudger and remove it from the device.

Linea Traguardo

Altre 21 persone hanno completato questa guida.

John

Membro da: 02/02/15

404 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 6-26, Amido Winter 2015 Membro di Cal Poly, Team 6-26, Amido Winter 2015

CPSU-AMIDO-W15S6G26

5 Membri

14 Guide realizzate

7 Commenti

Dear John,

Why must one disconnet the battery in step 3 and 4, whilst that does not seem necessary to replace the cable & port for the charger only (steps 5-10), and NOT the battery....?

Regards, Frank

Frank du Mee - Replica

Always disconnect battery and press power button a few times to rid of any power left on device while doing repairs. especially if you are using metal tools.

Oscar C - Replica

My Tab 2 10.1 does not come apart this way. If you try it this way, it will damage the touch screen connector. Plus the cable is different. This looks more like a Tab 1.

K Meeker - Replica

Does the P5100 have the same charging port as the P7500?

julia yapkew - Replica

I always open the tablet and order the cable by part and rev number. you may order a part for a tablet and will most like be sent for a diff version.

Oscar C -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 64

Tutti i Tempi: 38,784