Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert your fingernail or plastic opening tool into the divot at the top of the rear-facing camera.
-
Gently pry and twist the flexible rear cover off the back of the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Insert a fingernail or plastic opening tool into the recess in the bottom right corner of the battery and lift upward.
-
Remove the battery away from the phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a heat gun at an approximate distance of 2-3 inches from the phone to apply heat to the phone and loosen up the adhesive in the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Starting from the upper left corner, insert a guitar pick in between the display and the phone case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pick to pry the display by sliding the pick in the direction shown.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the pick to pry the sides and lower part of the display by sliding the pick through the phone.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the guitar pick, lift the screen slightly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slightly lift, but do not remove, the upper end of display assembly.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the sharp tip of a guitar pick to lift the front panel assembly cable connector straight up off its socket on the motherboard.
-
Safely remove the front panel assembly from phone.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a Phillips 0 screwdriver to remove all 12 Phillips #0 screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push upward from the back side your phone (where the battery should go) to pop out the large gray piece.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
You should now have two different pieces. To continue we will only use the piece with the motherboard (Shown on the right side of the picture).
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your finger or a plastic opening tool to disconnect the rear-facing camera from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your hands to gently remove the rear-facing camera from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your finger or a plastic opening tool to disconnect the proximity/light sensor from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use tweezers to gently pull the proximity/light sensor out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your finger or a plastic opening tool to disconnect the 3 button ribbon cable from the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to disconnect the the blue wire shown in the picture.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
After disconnecting the motherboard should come out easily.
-
Motherboard should look as shown in the picture.
-
Annulla: non ho completato questa guida.
Altre 19 persone hanno completato questa guida.