Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Introduzione

Does your phone not charge? Does the battery die quickly, no matter how long it stays on the charger? It could be a sign that a connection has come loose or that the port has been damaged. Replacing it could solve your problem.

Note that there are several different models of the S2 but this guide should help whether you have an international version of the phone or not.

  1. 1. Remove the rear casing and the battery. 2. Remove the SD card and the sim card (if needed).
    • 1. Remove the rear casing and the battery.

    • 2. Remove the SD card and the sim card (if needed).

  2. Use the Phillips screwdriver to remove the 7 Phillips head screws, indicated in the picture.
    • Use the Phillips screwdriver to remove the 7 Phillips head screws, indicated in the picture.

  3. Move along the outside edge with the plastic tool, popping the connections to the phone. The volume rocker and power button housing can be easily lost when you remove the back housing. Make sure you keep it where you can find it. The volume rocker and power button housing can be easily lost when you remove the back housing. Make sure you keep it where you can find it.
    • Move along the outside edge with the plastic tool, popping the connections to the phone.

    • The volume rocker and power button housing can be easily lost when you remove the back housing. Make sure you keep it where you can find it.

  4. Kit cacciaviti Manta

    112 punte per ogni riparazione.

    Upgrade Your Toolbox

    Kit cacciaviti Manta

    Upgrade Your Toolbox
  5. Remove the two black Phillips head screws located at the top left and the bottom right of the logic board.
    • Remove the two black Phillips head screws located at the top left and the bottom right of the logic board.

  6. Disconnect all push connectors and the antenna cable with a small pull shown on the left.
    • Disconnect all push connectors and the antenna cable with a small pull shown on the left.

  7. Prop the motherboard on the side of the phone.  Then take off the power button board (near the top of the antenna wire). Remove the 2 Phillips head screws located at the bottom of the charging board.
    • Prop the motherboard on the side of the phone. Then take off the power button board (near the top of the antenna wire).

    • Remove the 2 Phillips head screws located at the bottom of the charging board.

  8. Remove the board by prying off one end and moving toward the other. A hair dryer can help loosen the adhesive, but it is optional.
    • Remove the board by prying off one end and moving toward the other.

    • A hair dryer can help loosen the adhesive, but it is optional.

  9. Replace the old board with a new one. Replace the old board with a new one.
    • Replace the old board with a new one.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 20 persone hanno completato questa guida.

Hi all,

I have a Samsung Galaxy S2. The USB charging port is not working reliably. I read this repair guide, got the part, and set about replacing the USB charging board. Unfortunately, when I opened the phone, it does not look like the photos in this guide. To start, there are six screws instead of seven. Then when the back is removed, there are not "two black screws" to be removed. Finally, the motherboard is completely different from what is shown here. It is one single board, with the USB charging port board incorporated. It cannot be removed to replace it. So the part I bought does not work with my Samsung Galaxy S2. Is there another guide to help with my model of this phone?

Model SGH-T989

Many thanks.

rileybk - Replica

Hi rileybk, there are quite a number of phones called "Samsung Galaxy S2". Have a look at the Wikipedia here: https://en.wikipedia.org/wiki/Samsung_Ga...

The device shown here seems to be a SGH-I777 which you can read on the label below the battery.

As Wikipedia describes these devices can be very different from each other so that your replacement part might not fit or work at all.

(btw, I came by to look for a guide for the so-called "international version" i9100 ... I have to see whether this guide will help me nethertheless)

Steffan -

Need to buy new USBport and solder it to the motherboard, if there is no way to get new motherboard or replacement charging board.

ildafons - Replica

Does this work with a Galaxy S2 with a model number of SPH-0710?

Gp Smith - Replica

Whoops! I meant a a Galaxy S2 with a model number of SPH-D710.

Gp Smith - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 17

Ultimi 30 Giorni: 56

Tutti i Tempi: 11,277