Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Samsung Galaxy J1 Rear Camera Replacement

Scritto Da: Sean Kramer (e 2 altri collaboratori)
  • Commenti: 0
  • Preferiti: 2

Difficoltà

Moderato

Passi

8

Tempo Necessario

Suggerisci un tempo??

Sezioni

2

Contrassegni

0

Introduzione

Use this guide to replace the Rear Camera.

  1. Insert a finger nail or plastic opening tool between the back cover and the device.

    • Insert a finger nail or plastic opening tool between the back cover and the device.

    • Gently pry the rear cover off of the back of the phone.

    Modifica

  2. Using a finger, pull the SIM card down out of its slot. Remove the SIM card.

    • Using a finger, pull the SIM card down out of its slot.

    • Remove the SIM card.

    • The pictured device is missing the SIM card and battery.

    Modifica

  3. Using a Phillips #00 screwdriver remove the eleven 3 mm screws.

    • Using a Phillips #00 screwdriver remove the eleven 3 mm screws.

    Modifica

  4. Kit cacciaviti Manta

    112 punte per ogni riparazione.

    Upgrade Your Toolbox

    Kit cacciaviti Manta

    Upgrade Your Toolbox

  5. Insert a plastic opening tool between the screen and the back of the device. Starting at the bottom of the device, gently slide the tool along the edges of the screen. Gently pry the main assembly from the midframe of the device.

    • Insert a plastic opening tool between the screen and the back of the device.

    • Starting at the bottom of the device, gently slide the tool along the edges of the screen.

    • Gently pry the main assembly from the midframe of the device.

    • When removing the main assembly, pry gently so as to not crack the glass screen or break any clips within the device.

    Modifica

  6. Use the flat end of a spudger to disconnect the ear speaker connector from the motherboard. Use the flat end of a spudger to disconnect the ear speaker connector from the motherboard.

    • Use the flat end of a spudger to disconnect the ear speaker connector from the motherboard.

    Modifica

  7. Use the flat end of a spudger to disconnect the digitizer connector from the motherboard. Use the flat end of a spudger to disconnect the digitizer connector from the motherboard.

    • Use the flat end of a spudger to disconnect the digitizer connector from the motherboard.

    Modifica

  8. Use a plastic opening tool to gently pry under the motherboard. Remove motherboard. Remove motherboard.

    • Use a plastic opening tool to gently pry under the motherboard.

    • Remove motherboard.

    Modifica

  9. Use the flat end of a spudger to disconnect the rear camera from the motherboard. Remove the rear camera. Remove the rear camera.

    • Use the flat end of a spudger to disconnect the rear camera from the motherboard.

    • Remove the rear camera.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Sean Kramer

Membro da: 14/02/2018

1.212 Reputazione

6 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

USF Tampa, Team S5-G4, Eyestone Spring 2018 Membro di USF Tampa, Team S5-G4, Eyestone Spring 2018

USFT-EYESTONE-S18S5G4

3 Membri

6 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 35

Tutti i Tempi: 1,118