Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Scratch off the right-hand side of the sticker at the center of the bottom case using the spudger until the screw is visible.
    • Scratch off the right-hand side of the sticker at the center of the bottom case using the spudger until the screw is visible.

    • Remove this screw with the Phillips #000 screwdriver.

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the two visible screws on the bottom with the Phillips #000 screwdriver.
    • Remove the two visible screws on the bottom with the Phillips #000 screwdriver.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use your fingers to peel off the four corner rubber feet on the bottom. Use the Phillips #000 screwdriver to remove the four screws beneath the rubber feet.
    • Use your fingers to peel off the four corner rubber feet on the bottom.

    • Use the Phillips #000 screwdriver to remove the four screws beneath the rubber feet.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Flip the case to its upright position.
    • Flip the case to its upright position.

    • Place one hand on the bottom plate of the case and one on the top plate. Gently pull apart the two plates by tilting the top plate about the front of the device. Treat the front of the device as a hinge.

    • Remove the back cover from the device.

    • Be sure not to rip the wire connection of the LED bulb that is still connected to the bottom plate.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Unscrew the LED board on the inside of the top plate with the Phillips #000 screwdriver.
    • Unscrew the LED board on the inside of the top plate with the Phillips #000 screwdriver.

    • Note: The top plate is no longer needed for the next steps, so you can feel free to set it aside until reassembly.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use the Phillips #000 screwdriver to remove the five screws circled in the provided picture. The tan board can now detach from the rest of the case, as pictured, but you can feel free to leave it in place for now.
    • Use the Phillips #000 screwdriver to remove the five screws circled in the provided picture.

    • The tan board can now detach from the rest of the case, as pictured, but you can feel free to leave it in place for now.

    • CAUTION: Do not disconnect the tan power switch board from the grey ribbon cables.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Remove the smaller screws located on the green motherboard with the Phillips #000 screwdriver. Remove the two larger screws holding down the game cartridge slot with the Phillips #1 screwdriver.
    • Remove the smaller screws located on the green motherboard with the Phillips #000 screwdriver.

    • Remove the two larger screws holding down the game cartridge slot with the Phillips #1 screwdriver.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Gently remove the motherboard and the connected tan power switch board from the bottom plate. CAUTION: Be sure not to rip the ribbon cables connecting the motherboard and tan power switch board. CAUTION: Be sure not to rip the ribbon cables connecting the motherboard and tan power switch board.
    • Gently remove the motherboard and the connected tan power switch board from the bottom plate.

    • CAUTION: Be sure not to rip the ribbon cables connecting the motherboard and tan power switch board.

Linea Traguardo

Un'altra persona ha completato questa guida.

Matthew Lawler

Membro da: 19/04/2018

237 Reputazione

1 Guida realizzata

Team

Cal Poly, Team S24-G12, Maness Spring 2018 Membro di Cal Poly, Team S24-G12, Maness Spring 2018

CPSU-MANESS-S18S24G12

4 Membri

10 Guide realizzate

Gday!

I recived a Sega HD Flashback 85 for Xmax. When I turned ON the game I have sound on the main menu but not when I played the game.

I went on the at@game to download there firware for the good console since my uptade I don’t have any video game anymore. I rename the file name on my SD Card like the instruction with anysucces. When I installed the SD card with the last firware and turn ON the console it update for ever without rest upload and turn ON the new update.

ERIC GUAY

ERIC GUAY - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 18

Tutti i Tempi: 1,107