Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Rival Mini Chopper MC-67BL Turning Gears Replacement

Cosa ti serve

  1. Rival Mini Chopper MC-67BL Turning Gears Replacement, Turning Gears: passo 1, immagine 1 di 2 Rival Mini Chopper MC-67BL Turning Gears Replacement, Turning Gears: passo 1, immagine 2 di 2
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

  2. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 2, immagine 1 di 1
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

  3. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 3, immagine 1 di 1
    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

  4. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 4, immagine 1 di 1
    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

  5. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 5, immagine 1 di 2 Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 5, immagine 2 di 2
    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

  6. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 6, immagine 1 di 1
    • Firmly lift the bottom cover off of the base.

  7. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 7, immagine 1 di 1
    • Remove the smaller white gear by lifting it up with your hand.

  8. Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 8, immagine 1 di 3 Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 8, immagine 2 di 3 Rival Mini Chopper MC-67BL Turning Gears Replacement: passo 8, immagine 3 di 3
    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Roxanne

Membro da: 10/17/13

522 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 4-29, Amido Fall 2013 Membro di Cal Poly, Team 4-29, Amido Fall 2013

CPSU-AMIDO-F13S4G29

4 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 5

Tutti i Tempi: 802