Introduzione

This guide will help you remove the safety latch for the container lid.

  1. Twist the plastic lid counterclockwise to unlock it.
    • Twist the plastic lid counterclockwise to unlock it.

    • Lift the lid to remove it from the container.

    Aggiungi Commento

  2. Carefully remove the blade from the container.
    • Carefully remove the blade from the container.

    • For reassembly, the teeth on the metal shaft line up with slots on the inside of the plastic hole.

    Aggiungi Commento

    • With your hand, twist the container counter-clockwise until it unlocks from the base. Remove the container by lifting it straight up.

    Aggiungi Commento

    • Use your fingers to pry out the two rubber feet from the bottom cover of the base.

    • The two feet furthest from the button tower contain screws. The other two feet do not.

    Aggiungi Commento

    • Use the Phillips #2 screwdriver to unscrew the two 12.7-mm screws underneath the rubber feet.

    • Use the same screwdriver to unscrew the 15.88-mm screw from the back of the chopper.

    Aggiungi Commento

    • Firmly lift the bottom cover off of the base.

    Aggiungi Commento

  3. Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    • Remove the smaller white gear by lifting it up with your hand.

    Aggiungi Commento

    • Use a pair of pliers or any other clamping tool to securely hold the blade-shaft that sits above the base.

    • Grab the gear with your other hand and turn CLOCKWISE. Unlike most screws, the gear is reverse-threaded to allow the blade to spin.

    • Continue turning the gear until completely removed from the blade-shaft.

    Aggiungi Commento

    • Use your hand to firmly pull the blade-shaft from the base.

    Aggiungi Commento

    • Using Phillips #2 screwdriver, unscrew two 12.7-mm screws in the middle of the base.

    Aggiungi Commento

    • Unwind power cord from the base pegs.

    Aggiungi Commento

    • Use the plastic opening tool to pry open the base from the main body.

    • These two plastic prongs are pressed fit into the base. It may take some effort to pry the base completely off.

    • Once freed, lift the base panel from the main body and set it aside.

    Aggiungi Commento

    • Use a Phillips #2 screwdriver to remove the three 9.53-mm screws from inside the main body.

    • Next, turn the device upright and lift the upper casing from around the button gently.

    Aggiungi Commento

    • Remove the button by simply pulling it up.

    • Don't lose the spring under the button! Without it, the blender will not function.

    Aggiungi Commento

    • Use the Phillips #2 screwdriver to remove one 9.53-mm screw.

    Aggiungi Commento

    • Remove the white latch by unhooking it from the spring wire and gently lifting straight up.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Roxanne

Membro da: 17/10/2013

507 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 4-29, Amido Fall 2013 Membro di Cal Poly, Team 4-29, Amido Fall 2013

CPSU-AMIDO-F13S4G29

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 6

Tutti i Tempi: 1,214