Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Ricoh Theta S Internal microSD Replacement

Cosa ti serve

  1. Ricoh Theta S Internal microSD Replacement, Outer Case: passo 1, immagine 1 di 1
    • Wedge the spudger underneath the small plastic square located on the bottom of the device.

    • Move the spudger to remove the plastic cover.

  2. Ricoh Theta S Internal microSD Replacement: passo 2, immagine 1 di 2 Ricoh Theta S Internal microSD Replacement: passo 2, immagine 2 di 2
    • Remove the four 3-mm screws located on the bottom of the device. You will need to use the Phillips 00 screwdriver.

  3. Ricoh Theta S Internal microSD Replacement: passo 3, immagine 1 di 3 Ricoh Theta S Internal microSD Replacement: passo 3, immagine 2 di 3 Ricoh Theta S Internal microSD Replacement: passo 3, immagine 3 di 3
    • Insert the plastic opening tool in between the panels shown.

    • Apply pressure to unlatch the 9 spring clips located around the perimeter of the device.

    • Lift the panel from the device.

  4. Ricoh Theta S Internal microSD Replacement, Battery: passo 4, immagine 1 di 2 Ricoh Theta S Internal microSD Replacement, Battery: passo 4, immagine 2 di 2
    • The battery is located near the bottom of the device.

    • Flip the plastic containing thermal compound over so it is resting on top of the battery.

  5. Ricoh Theta S Internal microSD Replacement: passo 5, immagine 1 di 2 Ricoh Theta S Internal microSD Replacement: passo 5, immagine 2 di 2
    • Lift the battery out of the device, beginning with the end closest to the camera.

  6. Ricoh Theta S Internal microSD Replacement, Internal microSD: passo 6, immagine 1 di 1
    • Remove the two 2mm Phillips screws.

    • Remove the black 2mm Phillips screw.

    • Remove the 1.5mm Phillips screw.

  7. Ricoh Theta S Internal microSD Replacement: passo 7, immagine 1 di 3 Ricoh Theta S Internal microSD Replacement: passo 7, immagine 2 di 3 Ricoh Theta S Internal microSD Replacement: passo 7, immagine 3 di 3
    • Carefully pull the side casing away from the camera.

  8. Ricoh Theta S Internal microSD Replacement: passo 8, immagine 1 di 3 Ricoh Theta S Internal microSD Replacement: passo 8, immagine 2 di 3 Ricoh Theta S Internal microSD Replacement: passo 8, immagine 3 di 3
    • Lift up the plastic containing thermal compound to reveal the thermal tape covering the motherboard.

    • Peel back the lower left corner of the thermal tape to reveal the microSD slot located on the motherboard.

  9. Ricoh Theta S Internal microSD Replacement: passo 9, immagine 1 di 2 Ricoh Theta S Internal microSD Replacement: passo 9, immagine 2 di 2
    • Push the microSD card inward, from the side.

    • Once a click is heard, pull the screwdriver away to eject the microSD card from the slot.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Team

IUPUI, Team S3-G1, Harley Fall 2017 Membro di IUPUI, Team S3-G1, Harley Fall 2017

IUPUI-HARLEY-F17S3G1

3 Membri

4 Guide realizzate

8 Commenti

I was able to complete this however there is a clear plastic guard running around the bottom half of the Theta S, and the only way to get the SD Card above that guard was to remove a few additional screws. Fortunately was not that complex and reassembly was still successful. Good luck!

jason - Replica

Maximum size of SD Card? 128GB?

just - Replica

I’ve not heard of anyone getting anything over 32gb to work, but I don’t think that’s definitive, as, even with 32GB cards, some would work and some wouldn’t. I think I might order a 64gb and try it out…

Basil Yokarinis -

I successfully replaced my microSD card with a transcend 32gb card, and it’s working. Only thing is, I ended up with 2 tiny braided wire sleeves that fell out during the process, and I have no idea where they are supposed to be. Also, before the repair, I had, an error come up at random and stop interval shooting (while there was still space available and power):

_cameraError":[“FORMAT_CARD”]

Now, after the repair, the error is:

_cameraError":["FORMAT_INTERNAL_MEM"]

And it’s constant, but, aside from causing the red lamp to blink always, and also beeping when I turn it on, it doesn’t seem to affect the function of the camera.

One point to improve the tutorial would be in step 8, in the 3rd picture, there’s a metallic, odd shaped piece sitting at an angle in the picture. This piece fell out when I was working to replace the microSD card, and I had to search other tutorials to figure out where it had to go.

Basil Yokarinis - Replica

Correction, it was a Sandisk Ultra

Basil Yokarinis -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 25

Tutti i Tempi: 3,796