Aggiusta la tua roba Comunità Store

Retroid Pocket 3 Motherboard Replacement

Introduzione

If the device is not turning on at all and is not responding, follow this guide to do a mainboard replacement (PCB) on the device. This process will take approximately 20-25 minutes, and the tools needed for the project are listed in the guide.


Cosa ti serve

  1. Retroid Pocket 3 Motherboard Replacement, Battery: passo 1, immagine 1 di 1

    • Unplug any cables connected to the Retroid Pocket 3+.

    • Ensure your device has a charge of 5% or less as a charged battery can be dangerous if punctured.

    Traduci

  2. Retroid Pocket 3 Motherboard Replacement: passo 2, immagine 1 di 3 Retroid Pocket 3 Motherboard Replacement: passo 2, immagine 2 di 3 Retroid Pocket 3 Motherboard Replacement: passo 2, immagine 3 di 3

    • Remove the four 6 mm screws from the backplate of the device with a T5 Torx screwdriver.

    • Use a plastic opening tool or spudger to gently pry apart the backplate from the device.

    Traduci

  3. Retroid Pocket 3 Motherboard Replacement: passo 3, immagine 1 di 2 Retroid Pocket 3 Motherboard Replacement: passo 3, immagine 2 di 2

    • Remove the four 4.5 mm screws with a Phillips #00 screwdriver.

    • Lift off the metal plate.

    Traduci

  4. Retroid Pocket 3 Motherboard Replacement: passo 4, immagine 1 di 3 Retroid Pocket 3 Motherboard Replacement: passo 4, immagine 2 di 3 Retroid Pocket 3 Motherboard Replacement: passo 4, immagine 3 di 3

    • Use a plastic opening tool or spudger to unclip the battery connector.

    • Carefully lift the battery from the case.

    • The battery has double-sided tape at the bottom. Gently push a spudger or opening tool underneath the battery to help free it from the adhesive. Do not bend or puncture the battery.

    • Lift and remove the battery.

    Traduci

  6. Retroid Pocket 3 Motherboard Replacement, Motherboard: passo 5, immagine 1 di 1

    • Remove the three 4.5 mm screws with a Phillips #00 screwdriver on the main board.

    Traduci

  7. Retroid Pocket 3 Motherboard Replacement: passo 6, immagine 1 di 1

    • Using a spudger, put the tip under the aerial connecter and rotate upwards to unclip the plug.

    Traduci

  8. Retroid Pocket 3 Motherboard Replacement: passo 7, immagine 1 di 1

    • Unclip and remove the one ribbon cable on the left.

    Traduci

  9. Retroid Pocket 3 Motherboard Replacement: passo 8, immagine 1 di 1

    • Use a spudger to unclip and remove the two ribbon cables on the right side.

    Traduci

  10. Retroid Pocket 3 Motherboard Replacement: passo 9, immagine 1 di 2 Retroid Pocket 3 Motherboard Replacement: passo 9, immagine 2 di 2

    • Use a spudger to disconnect the two speaker cables on the bottom of the board.

    Traduci

  11. Retroid Pocket 3 Motherboard Replacement: passo 10, immagine 1 di 3 Retroid Pocket 3 Motherboard Replacement: passo 10, immagine 2 di 3 Retroid Pocket 3 Motherboard Replacement: passo 10, immagine 3 di 3

    • Start lifting the board to give you access to the vibration motor on the metal case.

    • Use a spudger to carefully pry the motor free; it is bound with double-sided tape.

    • Carefully lift the board out of the device.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 18

Tutti i Tempi: 56