Aggiusta la tua roba Comunità Store

Replacing the gasket/seal of the brewing unit of Saeco XSmall

Introduzione

The seals/gaskets of any brewing unit are under constant strain. Particularly the large O-Ring on the piston needs replacing from time to time. These instructions show how this is done.

Cosa ti serve

  1. Replacing the gasket/seal of the brewing unit of Saeco XSmall, Brewing unit gasket: passo 1, immagine 1 di 2 Replacing the gasket/seal of the brewing unit of Saeco XSmall, Brewing unit gasket: passo 1, immagine 2 di 2

    • Open the hatch on the side panel and remove the brewing unit.

    Traduci

  2. Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 2, immagine 1 di 1

    • The spout for the hot coffee is located on the top of the brewing unit. It is fastened with two screws. Underneath is the crema valve. It consists of a spring and a little glass ball. Make sure the spring is reinserted with the thin end touching the glass ball when re-assembling.

    • Remove the two Torx T10 screws on the crema valve.

    • Lift off the crema valve minding the spring and the glass ball.

    Traduci

  4. Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 3, immagine 1 di 1

    • The upper piston is held in place in the frame with four locking pawls. Push down all four latches with a spudger, then remove the piston by pushing it downward.

    • If you want to replace the gasket, you can do this now and re-assemble the device and stop here. However, a general maintenance of the brewing unit is strongly recommended.

    • Unscrew the Torx T10 screw on the brewing sieve and remove it.

    Traduci

  5. Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 4, immagine 1 di 3 Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 4, immagine 2 di 3 Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 4, immagine 3 di 3

    • There are three Torx T10 screws in deep blind holes that hold together the two parts of the brewing unit. Unscrew them and lift off the upper side panel.

    Traduci

  6. Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 5, immagine 1 di 2 Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 5, immagine 2 di 2

    • Now you can disassemble the brewing unit into its three main parts: the brewing unit and the two side panels.

    Traduci

  7. Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 6, immagine 1 di 2 Replacing the gasket/seal of the brewing unit of Saeco XSmall: passo 6, immagine 2 di 2

    • You can push out the lower piston from the brewing unit if you snap the deflection lever out of its socket with a screw driver.

    • Clean all parts with very hot water and dishwasher liquid.

    • Grease all moving parts with food grade silicone fat. Dont forget the tracks in the side panels.

    Traduci
Conclusione

Apply these steps in reverse order to re-assemble the device.

Altre 4 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

de en

100%

jana°

jana° ci sta aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

Autore

con 1 altro collaboratore

VauWeh

Membro da: 10/19/15

205.301 Reputazione

250 Guide realizzate

Distintivi: 44

+41 altri distintivi

Team

Repair is War on Entropy Membro di Repair is War on Entropy

Community

25 Membri

1.148 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 27

Ultimi 30 Giorni: 132

Tutti i Tempi: 9,610