Introduzione

This repair guide will give you step by step instructions on how to remove the Macintosh PowerBook 1400c Monitor.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Aggiungi Commento

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Aggiungi Commento

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Aggiungi Commento

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

Aggiungi Commento

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

Aggiungi Commento

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Aggiungi Commento

Locate the speaker cover.
  • Locate the speaker cover.

Aggiungi Commento

Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Replica

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

Aggiungi Commento

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

Aggiungi Commento

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

Aggiungi Commento

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

Aggiungi Commento

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Replica

That isn't the HDD!

Dix Dox - Replica

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Aggiungi Commento

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

Aggiungi Commento

Remove the heatsink.
  • Remove the heatsink.

Aggiungi Commento

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Aggiungi Commento

Detach the ribbon cable.
  • Detach the ribbon cable.

Aggiungi Commento

Remove the keyboard.
  • Remove the keyboard.

Aggiungi Commento

Identify the right and left monitor end caps.
  • Identify the right and left monitor end caps.

Aggiungi Commento

Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.
  • Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.

Aggiungi Commento

Once the end cap has been loosened by the spudger, pull outwards on the end caps.
  • Once the end cap has been loosened by the spudger, pull outwards on the end caps.

Aggiungi Commento

Completely remove both end caps.
  • Completely remove both end caps.

Aggiungi Commento

Identify the 4 total screw under the end caps (2 under each end cap).
  • Identify the 4 total screw under the end caps (2 under each end cap).

    • The two outside 16mm long screws

    • The two inside 5.4mm long screws

Aggiungi Commento

Lay the monitor all the way back.
  • Lay the monitor all the way back.

Aggiungi Commento

Remove the 4 screws using the Phillips #0 screwdriver.
  • Remove the 4 screws using the Phillips #0 screwdriver.

Aggiungi Commento

Identify the center cap of the monitor.
  • Identify the center cap of the monitor.

Aggiungi Commento

Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.
  • Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.

Aggiungi Commento

Detach the center cap completely.
  • Detach the center cap completely.

Aggiungi Commento

Identify the one 12.6mm long screw under the center cap.
  • Identify the one 12.6mm long screw under the center cap.

Aggiungi Commento

Remove the center screw with a Phillips #0 screwdriver.
  • Remove the center screw with a Phillips #0 screwdriver.

Aggiungi Commento

Lift upwards on the metal cover under the screw.
  • Lift upwards on the metal cover under the screw.

Aggiungi Commento

Completely remove the metal cover.
  • Completely remove the metal cover.

Aggiungi Commento

Identify where the left and right monitor cords are attached to the logic board
  • Identify where the left and right monitor cords are attached to the logic board

    • The base of the left monitor cord

    • The base of the right monitor cord

Aggiungi Commento

To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.
  • To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.

Aggiungi Commento

Completely detach the left monitor cord from the logic board.
  • Completely detach the left monitor cord from the logic board.

Aggiungi Commento

To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.
  • To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.

Aggiungi Commento

Completely detach the right monitor cord from the logic board.
  • Completely detach the right monitor cord from the logic board.

Aggiungi Commento

Completely remove the monitor from the computer.
  • Completely remove the monitor from the computer.

Aggiungi Commento

Conclusione

Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Taylor Chris

Membro da: 01/04/2011

85 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 10-39, Forte Spring 2011 Membro di Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 10

Tutti i Tempi: 2,494