Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

  1. Assicurati che il tuo dispositivo sia spento prima di procedere. In caso contrario potresti subire scosse elettriche o danneggiare al dispositivo.
    • Assicurati che il tuo dispositivo sia spento prima di procedere. In caso contrario potresti subire scosse elettriche o danneggiare al dispositivo.

    • Disponi la 3DS al contrario. Rimuovi eventuali schede di gioco, cuffie, cavi di ricarica, stilo e qualsiasi altra cosa potrebbe essere connessa al dispositivo.

  2. Usando un cacciavite a croce JIS #0, svita le due viti nere posteriori.
    • Usando un cacciavite a croce JIS #0, svita le due viti nere posteriori.

    • Le viti sono trattenute in posizione da un rondella di fissaggio e non dovrebbero essere completamente rimosse.

  3. Quando le viti sono allentate, fai leva sulla cover posteriore.
    • Quando le viti sono allentate, fai leva sulla cover posteriore.

  4. La batteria è collocato sulla parte di sinistra della 3DS - per rimuoverla, sfrutta la piccola fenditura posta in alto al centro e fai leva con uno strumento appuntito.
    • La batteria è collocato sulla parte di sinistra della 3DS - per rimuoverla, sfrutta la piccola fenditura posta in alto al centro e fai leva con uno strumento appuntito.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a JIS #000 screwdriver, remove the six 6mm screws around the edges of the secondary cover.
    • Using a JIS #000 screwdriver, remove the six 6mm screws around the edges of the secondary cover.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using tweezers, carefully pop out the rubber bumpers located at the top side of the 3DS. Removing them will reveal another two 6mm screws. Remove these screws using a JIS #000 as well. Using tweezers, carefully pop out the rubber bumpers located at the top side of the 3DS. Removing them will reveal another two 6mm screws. Remove these screws using a JIS #000 as well.
    • Using tweezers, carefully pop out the rubber bumpers located at the top side of the 3DS. Removing them will reveal another two 6mm screws. Remove these screws using a JIS #000 as well.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    To separate the cover, carefully lift it up and away from the hinges (in order to clear the headphone port), then pivot it towards the hinges to expose the circuit boards. Don't fully remove the cover yet, or you may damage the delicate ribbon cable that still connects it to the motherboard. Don't fully remove the cover yet, or you may damage the delicate ribbon cable that still connects it to the motherboard.
    • To separate the cover, carefully lift it up and away from the hinges (in order to clear the headphone port), then pivot it towards the hinges to expose the circuit boards.

    • Don't fully remove the cover yet, or you may damage the delicate ribbon cable that still connects it to the motherboard.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use a pair of tweezers to lift away the two plugs that latch the L/R/ZL/ZR button ribbons to the motherboard. You can now remove the back cover completely and set it aside.
    • Use a pair of tweezers to lift away the two plugs that latch the L/R/ZL/ZR button ribbons to the motherboard. You can now remove the back cover completely and set it aside.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Use tweezers to flip up the small, hinged locking flap in order to unlock the ZIF connector securing the circle pad ribbon.
    • Use tweezers to flip up the small, hinged locking flap in order to unlock the ZIF connector securing the circle pad ribbon.

    • Slide the ribbon out of the ZIF connector.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a JIS #000 screwdriver, remove the two 8 mm screws securing the circle pad.
    • Using a JIS #000 screwdriver, remove the two 8 mm screws securing the circle pad.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Lift the circle pad casing upward to remove it. There will be some friction, but it should not require excessive force.
    • Lift the circle pad casing upward to remove it. There will be some friction, but it should not require excessive force.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Locate the gold terminal plug with a red cable at the top left of the motherboard. Using your fingers, carefully pull the plug straight upward to remove.
    • Locate the gold terminal plug with a red cable at the top left of the motherboard. Using your fingers, carefully pull the plug straight upward to remove.

    • Use a pair of tweezers to disconnect the single ribbon connector.

    • Don't do what we did -- be very careful not to pull on the red cable.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using tweezers, gently pull the five marked ribbons out of the ZIF connectors along the sides of the motherboard. These ZIF connectors are held in place by friction and do not have locks—lifting the flaps on these connectors will break them! Note that in some models the upper-most connector may have a lock. Three of the ribbon connectors have plastic clamping flaps that cover the ribbon to prevent slippage. Use the tweezers to flip them up before ribbon removal.
    • Using tweezers, gently pull the five marked ribbons out of the ZIF connectors along the sides of the motherboard.

    • These ZIF connectors are held in place by friction and do not have locks—lifting the flaps on these connectors will break them! Note that in some models the upper-most connector may have a lock.

    • Three of the ribbon connectors have plastic clamping flaps that cover the ribbon to prevent slippage. Use the tweezers to flip them up before ribbon removal.

    • When reassembling the device, be sure to flip the ZIF clamps back down.

    • While the SD card reader is shown as removed in this photo, it is optional for the removal of the motherboard.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Using a JIS #000 screwdriver, remove six 4mm screws along the edges of the motherboard.
    • Using a JIS #000 screwdriver, remove six 4mm screws along the edges of the motherboard.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Carefully pivot the motherboard 90 degrees toward the hinges to reveal two more ZIF connectors on the underside of the motherboard. Both have latches that must be flipped up. The left, longer latch is black; the right, shorter one is white. Flip up the flaps, slide the ribbons out and remove the motherboard.
    • Carefully pivot the motherboard 90 degrees toward the hinges to reveal two more ZIF connectors on the underside of the motherboard.

    • Both have latches that must be flipped up. The left, longer latch is black; the right, shorter one is white. Flip up the flaps, slide the ribbons out and remove the motherboard.

    • Note which way the ribbons slide into their connectors carefully, as they are different.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    A l'aide d'un tournevis JIS #000 enlevez les 3 vis Retirez ensuite le lecteur de  cartouches en le soulevant.
    • A l'aide d'un tournevis JIS #000 enlevez les 3 vis

    • Retirez ensuite le lecteur de cartouches en le soulevant.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    La pièce marquée en rouge est le support de l'antenne NFC, il faut l'enlever avant d'accéder au bloc LCD/Tactile. Dégager les clips du support plastique de l'antenne NFC à l'aide d'un outil fin sur le haut et le bas puis le détacher.
    • La pièce marquée en rouge est le support de l'antenne NFC, il faut l'enlever avant d'accéder au bloc LCD/Tactile.

    • Dégager les clips du support plastique de l'antenne NFC à l'aide d'un outil fin sur le haut et le bas puis le détacher.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Glisser un outil plat entre le support noir du LCD/Tactile et le carter de la console puis soulevez le doucement. Glissez ensuite un métronome dessous pour le maintenir. La nappe fléchée en rouge n'est pas vraiment génante mais il faut quand même faire attention à ne pas l'endommager pendant cette étape. Ensuite, vous pouvez soit soulever l'ensemble par dessous en le poussant vers le haut, soit continuer à faire le tour pour déclipser l'ensemble et l'extraire.
    • Glisser un outil plat entre le support noir du LCD/Tactile et le carter de la console puis soulevez le doucement. Glissez ensuite un métronome dessous pour le maintenir.

    • La nappe fléchée en rouge n'est pas vraiment génante mais il faut quand même faire attention à ne pas l'endommager pendant cette étape.

    • Ensuite, vous pouvez soit soulever l'ensemble par dessous en le poussant vers le haut, soit continuer à faire le tour pour déclipser l'ensemble et l'extraire.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Glissez un outil fin entre le LCD et le carter noir de l'ensemble puis soulevez doucement. le LCD sort sans forcer.
    • Glissez un outil fin entre le LCD et le carter noir de l'ensemble puis soulevez doucement. le LCD sort sans forcer.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    Chauffez les contours du tactile pour le décoller plus facilement puis poussez le doucement par dessous avec les doigts pour l'extraire. Chauffez les contours du tactile pour le décoller plus facilement puis poussez le doucement par dessous avec les doigts pour l'extraire.
    • Chauffez les contours du tactile pour le décoller plus facilement puis poussez le doucement par dessous avec les doigts pour l'extraire.

Linea Traguardo

Altre 11 persone hanno completato questa guida.

Guillaume Blas

Membro da: 20/12/2016

1.034 Reputazione

1 Guida realizzata

Team

Francophones Membro di Francophones

Community

19 Membri

8 Guide realizzate

I followed this guide to the letter last night on my hyrule gold new 3ds XL (from hence forth I will refer to this unit as my “old n3dsXL”) before attempting the same repair on my new unit. It worked fine on my old n3dsXL. So I went ahead with doing the same repair on my new unit.

Well it went fine till I tried to turn it on. The blue light comes on then after a few seconds there’s a “pop” sound and the unit turns back off. Can anyone tell me what just happened here?

Also tried putting the original touch screen back in the new unit and it still does the same pop sound and shuts off

Rachel Bell - Replica

You might need to reseat the cables i had this issue on my old ds lite and my old n3ds all i had to do was that and it fixed it for me also if that doesn’t work get a cotton swab and dip it in rubbing alcohol and clean the end of the ribbon cables then re insert them.

Joseph Federico -

Same thing happened to me my first time—brief blue light but would not power on. Tore it down and re-connected all the cables more carefully the second time. That fixed it.

BBW -

I just disassembled my new 3ds xl to clean my lower screen and touch sensor following this guide, it went smoothly but now everything works except the touch sensor, why??

Francesco Baldacchini - Replica

I have done this successfully three times now—thank you for the excellent guide. Newcomers should know there is one ERROR and one OMISSION in the procedure. (1) ERROR - In Step 13, the topmost ZIF connector marked in red *does* have a clamp, unlike the other four. If you attempt to pull the connector loose without opening the clamp you will break it—see the frustrated comments to Step 13 for examples. (2) OMISSION - At Step 16, before removing the cartridge drive you must unplug the connector at the top of the component. This is shown as unplugged in the photo, but the step is missing from the written instructions. The clamp on this plug loosens on the *opposite* side from where the cable is inserted, unlike the other clamps in the guide.

BBW - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 4

Ultimi 7 Giorni: 37

Ultimi 30 Giorni: 292

Tutti i Tempi: 10,718