Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
-
Gira la vite che blocca lo schermo così che questa sia parallela alla barra spaziatrice.
-
Tira verso di te le alette di rilascio della tastiera e solleva la tastiera finché non si libera.
-
Solleva la tastiera e rimuovila tirandola su e via da te. Posa la tastiera, a faccia in giù, sopra al track pad.
-
-
-
Rimuovi le due viti a croce Phillips #1 d’argento che fissano lo scudo termico alla struttura metallica interna.
-
Solleva lo scudo termico e tiralo verso di te.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Firmly grasp the plastic tab attached to the Airport card and pull up and then to the right.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the antenna cable from the Airport card.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pull the battery cable directly up from the logic board.
-
Remove the battery from its holder by pulling up and to the left.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Your laptop should look approximately like this.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the long silver Phillips #1 screw from the heat sink.
-
Remove the two T8 Torx screws that attach the heat sink to the processor.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the heat sink up from the left side and pull it out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the plastic tab on the processor's right side and pull it directly up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Your laptop should look approximately like this.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the black Torx screw from the right side of the modem.
-
Remove the small black plastic rectangle with four holes.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the tips of your fingers, a spudger, or a flat non-metal tool to get under the modem's edge and pry it up from its socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the cable from the right side of the modem.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Your laptop should look approximately like this.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the display back so that it lies flat.
-
Slip your index finger or a nylon tool under the clutch cover near the power button and pull gently upward until you feel it come free.
-
Repeat the previous step on the left side.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the clutch cover up and off, rotating it toward yourself.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the orange display data cable and disconnect it from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the single black Torx screw that fastens the display cable to the plastic casing.
-
Grasp the thin display inverter board at its left end; lift up and rotate toward yourself.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the white inverter cable from the right end of the board
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the inverter plug, pulling directly up from the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the laptop around so that its back faces you.
-
Open the port door located at the back of the laptop.
-
Remove the four black Torx screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Returning to the front, pull the black Airport antenna up from its recessed housing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold the display on both sides and pull directly up until its hinges are free of their mounts.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Your laptop should look approximately like this.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the wide orange cable that connects the airport card slot to the logic board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three long silver and one short black Torx screws from the beige plastic casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Slide the thin plastic shield away from you, out from under the black casing.
-
Disconnect the newly revealed thin orange ribbon from the logic board.
-
Remove the two long silver Torx screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the laptop over.
-
Remove the five short Torx screws from the bottom casing.
-
Remove the two long Torx screws in the front left and front right corners; make sure to put these back in the proper place when reassembling.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the laptop back over.
-
Remove three short black Torx screws from the metal frame.
-
Remove the small Torx screw to the far left that fastens the logic board to the casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grasp the upper plastic casing where it locks into the internal frame and pull back. When the plastic tab has cleared the slot that the casing locks into, pull up enough to keep it from locking back into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
The PC card eject button on the laptop's left side prevents the upper casing from lifting up. In order to bypass the button, push it in far enough so that you can pull the upper casing's left side out and up beyond the button.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the left side of the case partly up so that you can access and disconnect the audio in/out cables from the sound card in the upper right of the case.
-
Remove the upper casing. Note that there are two tabs on the laptop's front that often cause the upper case to stick.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Your laptop should look approximately like this.
-
Annulla: non ho completato questa guida.
Altre 4 persone hanno completato questa guida.