Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. , Tastiera: passo 1, immagine 1 di 1
    • Gira la vite che blocca lo schermo così che questa sia parallela alla barra spaziatrice.

    • Tira verso di te le alette di rilascio della tastiera e solleva la tastiera finché non si libera.

    • Solleva la tastiera e rimuovila tirandola su e via da te. Posa la tastiera, a faccia in giù, sopra al track pad.

  2. : passo 2, immagine 1 di 1
    • Rimuovi il cavo a nastro della tastiera direttamente dalla scheda logica. Metti la tastiera da parte.

    • Il connettore potrebbe essere stretto. Scuoti delicatamente il connettore da parte a parte mentre lo tiri direttamente verso l'alto per liberarlo. Puoi utilizzare questa tecnica su molte delle schede e dei cavi che dovrai scollegare.

    • Assicurati che tu abbia rimosso la batteria del portatile e i moduli CD/DVD dalle baie di espansione prima di procedere.

  3. : passo 3, immagine 1 di 1
    • Il tuo computer dovrebbe assomigliare più o meno a questo.

  4. , Scudo termico: passo 4, immagine 1 di 1
    • Rimuovi le due viti a croce Phillips #1 d’argento che fissano lo scudo termico alla struttura metallica interna.

    • Solleva lo scudo termico e tiralo verso di te.

  5. : passo 5, immagine 1 di 1
    • Il tuo computer dovrebbe presentarsi approssimativamente in questo modo.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 1
    • Skip this step if your computer does not have an Airport card installed.

    • Firmly grasp the plastic tab attached to the Airport card and pull up and then to the right.

    • The Airport card is still attached to the antenna cable, so don't just yank it out of the slot.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Disconnect the antenna cable from the Airport card.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 1
    • Pull the battery cable directly up from the logic board.

    • Remove the battery from its holder by pulling up and to the left.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 1
    • Your laptop should look approximately like this.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • Remove the long silver Phillips #1 screw from the heat sink.

    • Remove the two T8 Torx screws that attach the heat sink to the processor.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Lift the heat sink up from the left side and pull it out.

    • If you need to mount the heat sink back into the laptop, we have a thermal paste guide that makes replacing the thermal compound easy.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 1
    • Grasp the plastic tab on the processor's right side and pull it directly up.

    • Some processors may be missing the plastic pull tab. In this case, we suggest using a non-metal tool to gently pry up the processor. Slip the tool's thin edge under the front right corner of the processor and carefully pry it up.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 1
    • Your laptop should look approximately like this.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 1
    • Remove the black Torx screw from the right side of the modem.

    • Remove the small black plastic rectangle with four holes.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 1
    • Use the tips of your fingers, a spudger, or a flat non-metal tool to get under the modem's edge and pry it up from its socket.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 1
    • Disconnect the cable from the right side of the modem.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 1
    • Grasp the orange cable at the left end of the hard drive and disconnect it from the logic board.

    • Try to grasp the cable on the plastic connector rather than on the flexible cable section.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 1
    • Grasp the plastic tab and pull the hard drive up and to the left, making sure that the metal bracket doesn't catch on the black plastic casing.

  19. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 19, immagine 1 di 1
    • Your laptop should look approximately like this.

  20. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 20, immagine 1 di 1
    • Push the display back so that it lies flat.

    • Slip your index finger or a nylon tool under the clutch cover near the power button and pull gently upward until you feel it come free.

    • Repeat the previous step on the left side.

  21. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 21, immagine 1 di 1
    • Lift the clutch cover up and off, rotating it toward yourself.

  22. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 22, immagine 1 di 1
    • Grasp the orange display data cable and disconnect it from the logic board.

  23. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 23, immagine 1 di 1
    • Remove the single black Torx screw that fastens the display cable to the plastic casing.

    • Grasp the thin display inverter board at its left end; lift up and rotate toward yourself.

    • There are two tabs that hold the display inverter in place; these are what you need to get past in order to pull the board free.

  24. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 24, immagine 1 di 1
    • Disconnect the white inverter cable from the right end of the board

  25. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 25, immagine 1 di 1
    • Disconnect the inverter plug, pulling directly up from the logic board.

  26. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 26, immagine 1 di 1
    • Turn the laptop around so that its back faces you.

    • Open the port door located at the back of the laptop.

    • Remove the four black Torx screws.

  27. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 27, immagine 1 di 1
    • Returning to the front, pull the black Airport antenna up from its recessed housing.

  28. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Hold the display on both sides and pull directly up until its hinges are free of their mounts.

  29. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 29, immagine 1 di 1
    • Your laptop should look approximately like this.

Linea Traguardo

Altre 6 persone hanno completato questa guida.

Documenti Allegati

iRobot

Membro da: 09/24/09

1 Reputazione

636 Guide realizzate

Un commento

just ruined a new screen and a Pismo. I'm a genius

Patricia Bonarrigo - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 22

Tutti i Tempi: 14,400