Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Close the screen and turn the PowerBook over, orienting the computer upside down, using the label to guide you.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Hold the button on the front left side and slide the battery out.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With a Torx T8 screwdriver, remove the three Torx 24mm screws along the center of the back panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the computer over and open the display. You should see that the keyboard is loose.
-
Slightly lift the front of the keyboard up, and slide the keyboard towards yourself.
-
Carefully lift the top half of the keyboard and pull it towards yourself.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Loosen the ribbon cables connecting the keyboard to the computer by using a plastic opening tool to lift the tabs on either side of the cable port.
-
Gently remove the ribbons from its tabs.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently wiggle the RAM card to loosen the connection until it pulls free.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the 7mm screw connecting the speaker panel to the computer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
To detach the speaker panel's ribbon cable, use a plastic opening tool to lift the tabs on both sides of the cable port.
-
Once loose, pull the ribbon cable free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the lighting/audio panel from it's bottom corners and pull the panel towards yourself.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the display screen back to give yourself enough space to remove the side panels.
-
Remove the panels on either side by gently but firmly pulling up on them with both hands.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the plastic opening tool to lift up the tabs on either side of the ribbon cable port and then gently pull the ribbon cable free.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
With your index finger and your thumb, squeeze the track pad panel to loosen the clamps. Then slide the panel towards yourself.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the three T8 10mm long torx screws along the bottom of the casing next to the hard drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Rotate the hard drive towards yourself to access the ribbon cable and then gently pull up on the ribbon cable connector to remove the cable.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Place the hard drive so that the casing is facing up.
-
Remove the 4 T8 5mm long torx screws to remove the hard drive from the metal casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the metal casing off of the hard drive.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove and set aside the black protector that was under the hard drive casing.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to loosen the ribbon cable by running it along the connection and gently prying it free.
-
When you have loosened the connection, pull the tab to remove the ribbon cable.
-
Annulla: non ho completato questa guida.
Altre 6 persone hanno completato questa guida.