Aggiusta la tua roba Comunità Store

Playstation 3 Optical Drive Replacement

Guida Archiviata
Questa guida è mantenuta solo per scopi storici. Usa la versione aggiornata della guida per eseguire la riparazione.

Introduzione

This guide explains how to take apart the Sony PlayStation 3 optical drive. These steps are useful for repairing or replacing the optical drive.

Cosa ti serve

  1. Playstation 3 Optical Drive Replacement, Top Cover: passo 1, immagine 1 di 2 Playstation 3 Optical Drive Replacement, Top Cover: passo 1, immagine 2 di 2

    • Remove the rubber screw cover near the hard drive cover with a spudger.

    Modifica

  2. Playstation 3 Optical Drive Replacement: passo 2, immagine 1 di 1

    • Remove the screw holding the top cover in place with a Torx T10 screwdriver.

    Modifica

  3. Playstation 3 Optical Drive Replacement: passo 3, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 3, immagine 2 di 2

    • Slide the top cover down about half an inch.

    • Lift the cover off of the PS3.

    Modifica

  4. Playstation 3 Optical Drive Replacement: passo 4, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 4, immagine 2 di 2

    • Remove the seven screws in the top cover with a Phillips #2 screwdriver.

    • One of the screws is shorter than the others. The short screw is marked in yellow.

    Modifica

  5. Playstation 3 Optical Drive Replacement: passo 5, immagine 1 di 3 Playstation 3 Optical Drive Replacement: passo 5, immagine 2 di 3 Playstation 3 Optical Drive Replacement: passo 5, immagine 3 di 3

    • You can now lift off the top cover.

    Modifica

  6. Playstation 3 Optical Drive Replacement, Optical Drive: passo 6, immagine 1 di 3 Playstation 3 Optical Drive Replacement, Optical Drive: passo 6, immagine 2 di 3 Playstation 3 Optical Drive Replacement, Optical Drive: passo 6, immagine 3 di 3

    • Lift the optical drive enclosure and disconnect the grey wires.

    • Do not lift it too far up before disconnecting the wires.

    Modifica

  8. Playstation 3 Optical Drive Replacement: passo 7, immagine 1 di 3 Playstation 3 Optical Drive Replacement: passo 7, immagine 2 di 3 Playstation 3 Optical Drive Replacement: passo 7, immagine 3 di 3

    • Tilt the front of the optical drive enslosure upwards.

    • Lift the black ribbon cable latch on the back side with your finger or a spudger.

    • Disconnect the ribbon cable.

    Modifica

  9. Playstation 3 Optical Drive Replacement: passo 8, immagine 1 di 1

    • Remove the optical drive enclosure from the PS3.

    Modifica

  10. Playstation 3 Optical Drive Replacement: passo 9, immagine 1 di 3 Playstation 3 Optical Drive Replacement: passo 9, immagine 2 di 3 Playstation 3 Optical Drive Replacement: passo 9, immagine 3 di 3

    • Flip over the optical drive enclosure. There are four ribbon cables connected to the circuit board. Using a spudger or your finger, lift each ribbon cable latch and disconnect each ribbon cable.

    • Remove the three screws on the board with a Phillips #00 screwdriver.

    • Remove the two silver screws on the bottom of the case. These screws are different from the ones on the board and should be kept separate.

    • Note: The longer of these two screws holds down a metal tab that comes loose as seen in the third picture.

    Modifica

  11. Playstation 3 Optical Drive Replacement: passo 10, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 10, immagine 2 di 2

    • Using your thumbs, carefully bend out the sides of the metal enclosure.

    • Lift the plastic enclosure out of the metal enclosure.

    Modifica

  12. Playstation 3 Optical Drive Replacement: passo 11, immagine 1 di 3 Playstation 3 Optical Drive Replacement: passo 11, immagine 2 di 3 Playstation 3 Optical Drive Replacement: passo 11, immagine 3 di 3

    • Flip over the enclosure so that the circuit board is on the bottom and the optical sensor is on top.

    • Remove the screw on the optical sensor using a Phillips #00 screwdriver.

    • Remove the tape on the red and black wires that connect to the optical sensor. With the wires still attached, take the sensor off the ensclosure.

    • The wires on the optical sensor are very weak. They will break easily if excessive force is applied to them.

    • Remove the four black screws on the edges of the enclosure using a Phillips #00 screwdriver.

    • After taking out the screws, you don't have to open the enclosure just yet.

    Modifica

  13. Playstation 3 Optical Drive Replacement: passo 12, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 12, immagine 2 di 2

    • Flip over the enclosure again.

    • Remove the rest of the screws in the corners of the circuit board.

    Modifica

  14. Playstation 3 Optical Drive Replacement: passo 13, immagine 1 di 3 Playstation 3 Optical Drive Replacement: passo 13, immagine 2 di 3 Playstation 3 Optical Drive Replacement: passo 13, immagine 3 di 3

    • Lift the circuit board off the enclosure.

    • The metal EM shield on the circuit board is loose, so make sure to keep it together with the circuit board.

    • Remove the metal plate.

    Modifica

  15. Playstation 3 Optical Drive Replacement: passo 14, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 14, immagine 2 di 2

    • Flip over the enclosure. Remove the black, plastic cover so that the drive and its enclosure match the first picture.

    • Proceed carefully. There are loose parts inside the optical drive. We recommend that you tape these parts.

    Modifica

  16. Playstation 3 Optical Drive Replacement: passo 15, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 15, immagine 2 di 2

    • Using a spudger, lift the brown latch and disconnect the small ribbon cable.

    • Remove the four fat screws in the corners of the optical drive.

    • Using a spudger, lift the black latch and disconnect the larger ribbon cable.

    Modifica

  17. Playstation 3 Optical Drive Replacement: passo 16, immagine 1 di 2 Playstation 3 Optical Drive Replacement: passo 16, immagine 2 di 2

    • Carefully lift the optical drive out of the enclosure.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 9 altri collaboratori

iDeleted

Membro da: 07/07/10

2.101 Reputazione

39 Guide realizzate

Distintivi: 9

+6 altri distintivi

Un commento

When reassembling it there is a key part that needs to be exactly inline. see this video for help: http://www.youtube.com/watch?v=hzHPRGHFj...

Paddy - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 7,421