Salta al contenuto principale

Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.

Cosa ti serve

  1. , Smart Plate: passo 1, immagine 1 di 2 , Smart Plate: passo 1, immagine 2 di 2
    • Usa la punta di uno spudger per rimuovere dal lato della PS3 il coprivite in plastica nera.

    • Il coprivite può essere sotto un'etichetta di validità garanzia. Rimuovendola, comparirà la scritta "VOID".

  2. : passo 2, immagine 1 di 1
    • Rimuovi la singola vite da 8,5 mm tipo T10 Security Torx dalla smart plate.

  3. : passo 3, immagine 1 di 3 : passo 3, immagine 2 di 3 : passo 3, immagine 3 di 3
    • Tira la smart plate in direzione dell'alloggiamento dell'hard disk, poi sollevalo dalla PS3.

  4. : passo 4, immagine 1 di 1
    • Assicurati di non perdere la piccola staffa di metallo alloggiata, ma non fissata, nella cover superiore (se questa ne è dotata).

  5. , Cover Superiore: passo 5, immagine 1 di 1
    • Rimuovi le seguenti sette viti:

    • Sei viti Phillips da 52 mm

    • Una vite Phillips da 30 mm

  6. : passo 6, immagine 1 di 1
    • Solleva la cover superiore dal suo bordo posteriore e ruotano verso la parte anteriore della PS3.

    • Rimuovi la cover superiore.

    • C'è un gancio in plastica posizionato in un foro sul retro dell'angolo superiore destro. Spingi con delicatezza con uno spudger il gancio in plastica verso la parte posteriore della console in modo da liberare la parte posteriore destra della console.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 1
    • Remove the two 9 mm Phillips screws securing the memory card reader to the chassis.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 2 : passo 8, immagine 2 di 2
    • Lift the memory card reader out of the PS3 enough to access its cable.

    • Flip up the retaining flap on the memory card reader ribbon cable socket.

    • Be sure you are prying up on the retaining flap, not the socket itself.

    • Pull the ribbon cable out of its socket.

    • Remove the memory card reader from the PS3.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 1
    • Use the flat end of a spudger to pry the Wi-Fi antenna connector off its socket on the Wi-Fi/Bluetooth board.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 1
    • De-route the Wi-Fi antenna cable from the gap between the power supply and the Blu-ray drive.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 1
    • Remove the 9 mm Phillips screw securing the Wi-Fi antenna to the chassis.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 1
    • Remove the Wi-Fi antenna, minding its cable that may get caught.

Linea Traguardo

Altre 17 persone hanno completato questa guida.

3 Commenti

I used this guide to remove the stock antenna, learn my way through the PS3, and add a new external antenna. I removed the old one and bought an 8 inch 6 dbi antenna and a 12 inch R-SMA female pigtail adapter. Then drilled a hole with a 1/4" drill bit, attached the adapter, inserted the wire to the motherboard where the old one was connected, screwed on the antenna, and put everything back together. 5 times the internet speed!!! I did have to remove the power supply and disk drive however to get to the wire but still I never would have been able to complete this without the guide! Thanks to whoever did that! :D

The Pianoman - Replica

Pretty good guide! I just replaced my wifi antenna on my old ps3. I have to say that it was pretty easy since I never opened an ps3 before.

Michal S. - Replica

Yeah didn't quiet happen that way

Aaron Paul Bugg - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 25

Ultimi 30 Giorni: 96

Tutti i Tempi: 40,252