Aggiusta la tua roba

Diritto alla Riparazione

Store

Philips Sonicare 2 Series Circuit Board Replacement

Scritto Da: Jonathan Jarvis (e 3 altri collaboratori)
  • Commenti: 2
  • Preferiti: 0
  • Completamenti: 1

Difficoltà

Difficile

Passi

9

Tempo Necessario

20 minuti - 1 ora

Sezioni

2

Contrassegni

0

Introduzione

This guide will show you how to replace the circuit board for the Philips Sonicare 2 Series toothbrush. He is a link for a guide how to soldering which will be needed for this guide. Come saldare e dissaldare connessioni elettriche

  1. Remove brush on top of device.

    • Remove brush on top of device.

    Traduci

  2. Remove the 12 mm T8 Torx screw from the bottom of the toothbrush. After removing the screw, pry off the base with a plastic opening tool.

    • Remove the 12 mm T8 Torx screw from the bottom of the toothbrush. After removing the screw, pry off the base with a plastic opening tool.

    Traduci

  3. Remove the internal electronic mechanism from the housing by prying the red clips shown in the figure. This removes the charging port. Be very careful not to damage the charging port during this step. Otherwise you will have to solder this part back to the device as shown in the second figure.

    • Remove the internal electronic mechanism from the housing by prying the red clips shown in the figure. This removes the charging port.

    • Be very careful not to damage the charging port during this step. Otherwise you will have to solder this part back to the device as shown in the second figure.

    Traduci

  4. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

  5. Next you will be able to remove the internal electronic mechanism as shown in the figure.

    • Next you will be able to remove the internal electronic mechanism as shown in the figure.

    Traduci

  6. Remove the white battery cover as shown in the figure.

    • Remove the white battery cover as shown in the figure.

    Traduci

  7. Remove the white circuit board cover as shown. This cover will require you to pry off the piece from the groves .

    • Remove the white circuit board cover as shown. This cover will require you to pry off the piece from the groves .

    Traduci

  8. Pry away the battery using an opening tool from the battery housing. This will break the circuit and avoid electric shock.

    • Pry away the battery using an opening tool from the battery housing. This will break the circuit and avoid electric shock.

    Traduci

  9. Desolder the circuit board from the motor as shown.

    • Desolder the circuit board from the motor as shown.

    Traduci

  10. Desolder the circuit board from the housing as shown to remove the board

    • Desolder the circuit board from the housing as shown to remove the board

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 3 altri collaboratori

Jonathan Jarvis

Membro da: 01/04/2016

470 Reputazione

4 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

IUPUI, Team S6-G2, Baechle Fall 2017 Membro di IUPUI, Team S6-G2, Baechle Fall 2017

IUPUI-BAECHLE-F17S6G2

3 Membri

8 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 24

Tutti i Tempi: 795