Aggiusta la tua roba

Diritto alla Riparazione

Store

Philips DC320 37 Headphone or Power Jack Replacement

Scritto Da: Graham Rolph (e 5 altri collaboratori)
  • Commenti: 0
  • Preferiti: 0

Difficoltà

Facile

Passi

7

Tempo Necessario

10 - 20 minuti

Sezioni

2

Contrassegni

3

Confusing Text

Testo Confuso

Parte del testo di questa guida è confusionario, doppio, o fuori tema. Modificarlo per renderlo più chiaro!

Featured Student Guide

Guida Studente in Evidenza

Questa guida è frutto del duro lavoro dei nostri bravissimi studenti e il nostro staff iFixit la trova eccezionalmente brillante.

Action Shots

Foto Azione

Passa all'azione, eroe! Questa guida ha bisogno di immagini che meglio illustrano come eseguire azioni specifiche.

Introduzione

Follow the procedure outlined in this guide to remove and install a broken audio or power jack.

  1. Pry off the four white feet with the pointed end of the spudger

    • Pry off the four white feet with the pointed end of the spudger

    Traduci

  2. Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    • Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    Traduci

  3. Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • The connectors on the panel are fragile and may break.

    Traduci

  4. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Acquista ora

  5. Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock. Electrical Connectors Ribbon Connectors

    • Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock.

    • Electrical Connectors

    • Ribbon Connectors

    • The cables do not have a lot of slack in them. Be careful not to break the connectors.

    • One wire is soldered onto the bottom panel. Be careful not to break this bond.

    Traduci

  6. Unscrew the two 5 mm Phillips #00 screws attaching white support bracket to the body of the device.

    • Unscrew the two 5 mm Phillips #00 screws attaching white support bracket to the body of the device.

    Traduci

  7. Unscrew the two 5 mm Phillips #00 screws from green Headphone/Power electronics board to detach from white support bracket.

    • Unscrew the two 5 mm Phillips #00 screws from green Headphone/Power electronics board to detach from white support bracket.

    Traduci

  8. Separate the white suport bracket from the headphone/power electronics board.

    • Separate the white suport bracket from the headphone/power electronics board.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Graham Rolph

Membro da: 18/04/2013

1 Reputazione

2 Guide realizzate

Distintivi: 2

Team

Cal Poly, Team 3-48, Amido Spring 2013 Membro di Cal Poly, Team 3-48, Amido Spring 2013

CPSU-AMIDO-S13S3G48

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 9

Tutti i Tempi: 1,159