Salta al contenuto principale

Introduzione

A guide to get to and replace the camcorder's micophone.

Parti

Nessuna parte specificata.

  1. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.
    • Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.

  2. Open the tape compartment. Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.
    • Open the tape compartment.

    • Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.

  3. Use a plastic opening tool to remove the gray trim piece from top of the camcorder. Take care when removing the trim piece. The plastic parts are fragile and can break easily. Take care when removing the trim piece. The plastic parts are fragile and can break easily.
    • Use a plastic opening tool to remove the gray trim piece from top of the camcorder.

    • Take care when removing the trim piece. The plastic parts are fragile and can break easily.

  4. Rotate the camcorder so that the eye piece is facing you.
    • Rotate the camcorder so that the eye piece is facing you.

    • Remove the battery.

    • Remove the four black 4.5mm screws, sitting behind the battery.

    • Remove the 5th screw to the right of the battery dock.

    • Be careful not to lose any screws whilst trying to remove them.

  5. Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora

    Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora
  6. Rotate the camcorder so that the tape compartment is facing you. Remove the single 4.5mm black screw above the hook for the hand strap.
    • Rotate the camcorder so that the tape compartment is facing you.

    • Remove the single 4.5mm black screw above the hook for the hand strap.

    • Undoing the strap on one end may help.

    • Rotate the camcorder so that the lens is facing you.

    • Remove the single 4.5mm black screw from the front panel.

  7. Rotate the camcorder so that the bottom is facing towards you. Remove the single remaining 4.5mm black screw from the bottom.
    • Rotate the camcorder so that the bottom is facing towards you.

    • Remove the single remaining 4.5mm black screw from the bottom.

    • Remove the four silver 4.5mm screws from the body.

  8. Open the LCD screen on the side of the camcorder.
    • Open the LCD screen on the side of the camcorder.

    • Using a #00 screwdriver, remove the two 4.5mm silver screws located on either side of the hinge of the LCD screen.

  9. Very carefully remove the front cover from the main body of the camcorder. This should come apart with relative ease, however a plastic opening tool may help remove the panel.
    • Very carefully remove the front cover from the main body of the camcorder.

    • This should come apart with relative ease, however a plastic opening tool may help remove the panel.

    • There is a ribbon cable attached to the front panel and the camcorder body, so be careful not to pull that off when you remove this panel.

  10. Using your fingers, carefully pull the ribbon cable away from the logic board. Using your fingers, carefully pull the ribbon cable away from the logic board.
    • Using your fingers, carefully pull the ribbon cable away from the logic board.

  11. Using a #00 phillips screwdriver, remove the four 4mm screws holding the circuit board in place.
    • Using a #00 phillips screwdriver, remove the four 4mm screws holding the circuit board in place.

  12. Remove the circuit board containing the ribbon cable, microphone, and infared sensor. Remove the circuit board containing the ribbon cable, microphone, and infared sensor.
    • Remove the circuit board containing the ribbon cable, microphone, and infared sensor.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Joey Bradshaw

Membro da: 18/04/2010

10 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 7-9, Maness Spring 2010 Membro di Cal Poly, Team 7-9, Maness Spring 2010

CPSU-MANESS-S10S7G9

4 Membri

8 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 1,350